AI-generated solutions. The solutions and explanations on this page are written by AI. We check the final answers with automated tests, but AI can still make mistakes, especially in explanations and in figures described in words. If something looks wrong, ask in the doubt chat on that question or check with your teacher.

CBSE Class 12 Physics Sample Paper 2022-23 with Solutions

Step-by-step solutions to all 35 questions of the CBSE Class 12 Physics sample question paper for 2022-23, from electrostatics to semiconductors, written the way the marking scheme awards marks. Every key and number is checked against the official marking scheme and recomputed from the question, the places where the scheme slips are corrected and explained, the one question on a topic since dropped from the syllabus (the LED case study) is marked as such, and every question has a doubt chat.

CBSE Class 12 Physics Sample Question Paper 2022-23, subject code 042: 35 questions, 70 marks, 3 hours. Open any question to see the steps one at a time, ask a doubt about a step, or practise its chapter.

Section A: 18 MCQs of 1 mark each, including 3 assertion-reason questions

Q1

Question 1 (1 mark)

Chapter 1: Electric Charges and Fields
According to Coulomb's law, which is the correct relation for the following figure? (Figure: charges q1q_1 on the left and q2q_2 on the right on a straight line; the force F⃗12\vec F_{12} on q1q_1 points to the right, towards q2q_2, and the force F⃗21\vec F_{21} on q2q_2 points to the left, towards q1q_1.)
  1. (A)q1q2>0q_1 q_2 > 0
  2. (B)q1q2<0q_1 q_2 < 0
  3. (C)q1q2=0q_1 q_2 = 0
  4. (D)1>q1/q2>01 > q_1/q_2 > 0

Tests: Coulomb's law: the sign of the product of the charges decides attraction or repulsion.

Show solution
  1. Each force points towards the other charge, so the charges attract each other.
  2. Unlike charges attract: q1q_1 and q2q_2 have opposite signs, so q1q2<0q_1 q_2 < 0. (With q1q2>0q_1 q_2 > 0 the forces would point away from each other; with q1q2=0q_1 q_2 = 0 there would be no force.)
Answer(B) q1q2<0q_1 q_2 < 0
Ask about this question
Q2

Question 2 (1 mark)

Chapter 2: Electrostatic Potential and Capacitance
The electric potential on the axis of an electric dipole at a distance ‘r’ from it’s centre is V. Then the potential at a point at the same distance on its equatorial line will be
  1. (A)2V
  2. (B)-V
  3. (C)V/2
  4. (D)Zero

Tests: Potential of an electric dipole on its axis and on its equatorial line.

Show solution
  1. Potential of a dipole: V=14πε0pcos⁡θr2V = \dfrac{1}{4\pi\varepsilon_0}\dfrac{p\cos\theta}{r^2}, where θ\theta is measured from the dipole axis.
  2. On the equatorial line θ=90∘\theta = 90^\circ: every point is equidistant from +q+q and −q-q, so the two potentials cancel and V=0V = 0, whatever the axial value.
Answer(D) Zero
Ask about this question
Q3

Question 3 (1 mark)

Chapter 3: Current Electricity
The temperature (T) dependence of resistivity of materials A and material B is represented by fig (i) and fig (ii) respectively. Identify material A and material B. (Figures: in fig (i) the resistivity ρ falls steeply as T rises and then levels off; in fig (ii) ρ starts at a small value and rises ever more steeply with T.)
  1. (A)material A is copper and material B is germanium
  2. (B)material A is germanium and material B is copper
  3. (C)material A is nichrome and material B is germanium
  4. (D)material A is copper and material B is nichrome

Tests: Temperature dependence of resistivity for metals, alloys and semiconductors.

Show solution
  1. A: resistivity falls as the temperature rises. That is a semiconductor: heating frees more electron-hole pairs, so the number of carriers grows. Germanium.
  2. B: resistivity rises with temperature, and faster at higher T. That is a metal such as copper: the carriers stay the same in number but collide more often. (Nichrome's resistivity is high and rises only very slightly with temperature.)
Answer(B) material A is germanium and material B is copper
Ask about this question
Q4

Question 4 (1 mark)

Chapter 4: Moving Charges and Magnetism
Two concentric and coplanar circular loops P and Q have their radii in the ratio 2:3. Loop Q carries a current 9 A in the anticlockwise direction. For the magnetic field to be zero at the common centre, loop P must carry
  1. (A)3A in clockwise direction
  2. (B)9A in clockwise direction
  3. (C)6 A in anti-clockwise direction
  4. (D)6 A in the clockwise direction.

Tests: Magnetic field at the centre of a circular loop; superposition of fields.

Show solution
  1. Field at the centre of a loop: B=μ0I2rB = \dfrac{\mu_0 I}{2r}. The two fields must be equal and opposite, so P's current must flow the other way: clockwise.
  2. IPrP=IQrQ\dfrac{I_P}{r_P} = \dfrac{I_Q}{r_Q}, so IP=9×23=6I_P = 9 \times \dfrac{2}{3} = 6 A.
Answer(D) 6 A in the clockwise direction.
Ask about this question
Q5

Question 5 (1 mark)

Chapter 4: Moving Charges and Magnetism
A long straight wire of circular cross section of radius a carries a steady current I. The current is uniformly distributed across its cross section. The ratio of the magnitudes of magnetic field at a point distant a/2 above the surface of wire to that at a point distant a/2 below its surface is
  1. (A)4 :1
  2. (B)1:1
  3. (C)4: 3
  4. (D)3 :4

Tests: Ampère's law inside and outside a thick wire carrying a uniform current.

Show solution
  1. Above the surface the point is at r=a+a2=3a2r = a + \dfrac{a}{2} = \dfrac{3a}{2} from the axis (outside): B1=μ0I2πr=μ0I3πaB_1 = \dfrac{\mu_0 I}{2\pi r} = \dfrac{\mu_0 I}{3\pi a}.
  2. Below the surface the point is at r=a−a2=a2r = a - \dfrac{a}{2} = \dfrac{a}{2} (inside). Ampère's law with the enclosed current Ir2a2I\dfrac{r^2}{a^2} gives B2=μ0Ir2πa2=μ0I4πaB_2 = \dfrac{\mu_0 I r}{2\pi a^2} = \dfrac{\mu_0 I}{4\pi a}.
  3. B1B2=43\dfrac{B_1}{B_2} = \dfrac{4}{3}.
Answer(C) 4: 3
Ask about this question
Q6

Question 6 (1 mark)

Chapter 5: Magnetism and Matter
If the magnetizing field on a ferromagnetic material is increased, its permeability
  1. (A)decreases
  2. (B)increases
  3. (C)remains unchanged
  4. (D)first decreases and then increases

Tests: Permeability of a ferromagnet and magnetic saturation.

Show solution
  1. Permeability μ=BH\mu = \dfrac{B}{H}. In a ferromagnet the domains align with the field; as H grows, almost all are aligned and the magnetisation saturates.
  2. Beyond that, B grows only as μ0H\mu_0 H while H keeps growing, so BH\dfrac{B}{H} falls: the permeability decreases.

    Why: Strictly, at very small H, μ first rises a little and then falls; the marking scheme (and NCERT Exemplar) take the decrease, and no option offers 'first increases, then decreases'.

Answer(A) decreases
Ask about this question
Q7

Question 7 (1 mark)

Chapter 7: Alternating Current
An iron cored coil is connected in series with an electric bulb with an AC source as shown in figure. When iron piece is taken out of the coil, the brightness of the bulb will (Figure: a single loop with the coil, the bulb and the ac source in series.)
  1. (A)decrease
  2. (B)increase
  3. (C)remain unaffected
  4. (D)fluctuate

Tests: Effect of an iron core on inductance and inductive reactance.

Show solution
  1. Removing the iron core lowers the coil's inductance L (iron has a large permeability), so its reactance XL=ωLX_L = \omega L falls.
  2. The impedance Z=R2+XL2Z = \sqrt{R^2 + X_L^2} falls, the current rises and the bulb glows brighter.
Answer(B) increase
Ask about this question
Q8

Question 8 (1 mark)

Chapter 8: Electromagnetic Waves
Which of the following statement is NOT true about the properties of electromagnetic waves?
  1. (A)These waves do not require any material medium for their propagation
  2. (B)Both electric and magnetic field vectors attain the maxima and minima at the same time
  3. (C)The energy in electromagnetic wave is divided equally between electric and magnetic fields
  4. (D)Both electric and magnetic field vectors are parallel to each other

Tests: Properties of electromagnetic waves.

Show solution
  1. (A), (B), (C) are true: EM waves travel in vacuum, E and B oscillate in phase, and the average electric and magnetic energy densities are equal.
  2. (D) is false: E⃗\vec E and B⃗\vec B are perpendicular to each other and to the direction of propagation (E⃗×B⃗\vec E \times \vec B).
Answer(D) Both electric and magnetic field vectors are parallel to each other
Ask about this question
Q9

Question 9 (1 mark)

Chapter 6: Electromagnetic Induction
A rectangular, a square, a circular and an elliptical loop, all in the (x-y) plane, are moving out of a uniform magnetic field with a constant velocity v⃗=vi^\vec v = v\hat i. The magnetic field is directed along the negative z-axis direction. The induced emf, during the passage of these loops, out of the field region, will not remain constant for
  1. (A)any of the four loops
  2. (B)the circular and elliptical loops
  3. (C)the rectangular, circular and elliptical loops
  4. (D)only the elliptical loops

Tests: Motional emf: the rate of change of flux depends on the width of the loop at the boundary.

Show solution
  1. The emf is ε=B l v\varepsilon = B\,l\,v, where ll is the length of the loop's edge that is crossing the boundary of the field, perpendicular to v⃗\vec v.
  2. For the rectangle and the square (sides along the axes), that length is a side, the same all the way out: constant emf.
  3. For the circle and the ellipse, the chord at the boundary grows to the diameter (or axis) and shrinks again, so the rate of change of flux, and the emf, keep changing.

    Why: The figure is not given; the rectangle and square are read with their sides along x and y, as in the NCERT Exemplar question this follows.

Answer(B) the circular and elliptical loops
Ask about this question
Q10

Question 10 (1 mark)

Chapter 10: Wave Optics
In a Young’s double slit experiment, the path difference at a certain point on the screen between two interfering waves is 18\dfrac{1}{8}th of the wavelength. The ratio of intensity at this point to that at the centre of a bright fringe is close to
  1. (A)0.80
  2. (B)0.74
  3. (C)0.94
  4. (D)0.85

Tests: Intensity in Young's experiment in terms of the phase difference.

Show solution
  1. Phase difference ϕ=2πλ×λ8=π4\phi = \dfrac{2\pi}{\lambda} \times \dfrac{\lambda}{8} = \dfrac{\pi}{4}.
  2. I=I0cos⁡2ϕ2I = I_0\cos^2\dfrac{\phi}{2}, so II0=cos⁡2π8=1+cos⁡(π/4)2=1+0.7072≈0.85\dfrac{I}{I_0} = \cos^2\dfrac{\pi}{8} = \dfrac{1 + \cos(\pi/4)}{2} = \dfrac{1 + 0.707}{2} \approx 0.85.
Answer(D) 0.85
Ask about this question
Q11

Question 11 (1 mark)

Chapter 11: Dual Nature of Radiation and Matter
The work function for a metal surface is 4.14 eV. The threshold wavelength for this metal surface is:
  1. (A)4125 Å
  2. (B)2062.5 Å
  3. (C)3000 Å
  4. (D)6000 Å

Tests: Threshold wavelength from the work function.

Show solution
  1. λ0=hcϕ0\lambda_0 = \dfrac{hc}{\phi_0}, with hc≈12400hc \approx 12400 eV Å.
  2. λ0=124004.14≈2995\lambda_0 = \dfrac{12400}{4.14} \approx 2995 Å ≈3000\approx 3000 Å.
Answer(C) 3000 Å
Ask about this question
Q12

Question 12 (1 mark)

Chapter 12: Atoms
The radius of the innermost electron orbit of a hydrogen atom is 5.3×10−115.3 \times 10^{-11} m. The radius of the n =3 orbit is
  1. (A)1.01×10−101.01 \times 10^{-10} m
  2. (B)1.59×10−101.59 \times 10^{-10} m
  3. (C)2.12×10−102.12 \times 10^{-10} m
  4. (D)4.77×10−104.77 \times 10^{-10} m

Tests: Radius of the nth Bohr orbit.

Show solution
  1. Bohr orbits: rn=n2r1r_n = n^2 r_1.
  2. r3=9×5.3×10−11=4.77×10−10r_3 = 9 \times 5.3 \times 10^{-11} = 4.77 \times 10^{-10} m.
Answer(D) 4.77×10−104.77 \times 10^{-10} m
Ask about this question
Q13

Question 13 (1 mark)

Chapter 13: Nuclei
Which of the following statements about nuclear forces is not true?
  1. (A)The nuclear force between two nucleons falls rapidly to zero as their distance is more than a few femtometres.
  2. (B)The nuclear force is much weaker than the Coulomb force.
  3. (C)The force is attractive for distances larger than 0.8 fm and repulsive if they are separated by distances less than 0.8 fm.
  4. (D)The nuclear force between neutron-neutron, proton-neutron and proton-proton is approximately the same.

Tests: Properties of the nuclear force.

Show solution
  1. (A), (C) and (D) are true: the nuclear force is short ranged, repulsive below about 0.8 fm, and charge independent.
  2. (B) is false: the nuclear force is much stronger than the Coulomb force between protons; that is why it can hold the protons of a nucleus together.
Answer(B) The nuclear force is much weaker than the Coulomb force.
Ask about this question
Q14

Question 14 (1 mark)

Chapter 7: Alternating Current
If the reading of the voltmeter V1V_1 is 40 V, then the reading of voltmeter V2V_2 is (Figure: a resistor, an inductor and a capacitor in series with an ac source 502sin⁡ωt50\sqrt{2}\sin\omega t. Voltmeter V2V_2 is across the resistor alone; voltmeter V1V_1 is across the inductor and capacitor together.)
  1. (A)30 V
  2. (B)58 V
  3. (C)29 V
  4. (D)15 V

Tests: Phasor addition of voltages in a series LCR circuit.

Show solution
  1. The rms source voltage is 5022=50\dfrac{50\sqrt2}{\sqrt2} = 50 V. Voltmeters read rms values.
  2. VLV_L and VCV_C are opposite in phase, so V1=∣VL−VC∣=40V_1 = |V_L - V_C| = 40 V; VRV_R is 90° out of phase with them: V2=VR2+(VL−VC)2V^2 = V_R^2 + (V_L - V_C)^2.
  3. V2=VR=502−402=30V_2 = V_R = \sqrt{50^2 - 40^2} = 30 V.
Answer(A) 30 V
Ask about this question
Q15

Question 15 (1 mark)

Chapter 2: Electrostatic Potential and Capacitance
The electric potential V as a function of distance X is shown in the figure. (Figure: V rises linearly from 0 at X = 0 to a maximum at X = 2, stays constant from X = 2 to X = 4, and falls linearly back to 0 at X = 6.) The graph of the magnitude of electric field intensity E as a function of X is (Option graphs, E against X: (i) E = −E (constant) from 0 to 2, zero from 2 to 4, +E from 4 to 6. (ii) E rises linearly from 0 to +E between 0 and 2, drops to −E at 2, rises linearly back to 0 by 4, and is zero from 4 to 6. (iii) +E from 0 to 2, zero from 2 to 4, −E from 4 to 6. (iv) +E from 0 to 4, −E from 4 to 6.)
  1. (A)graph (i)
  2. (B)graph (ii)
  3. (C)graph (iii)
  4. (D)graph (iv)

Tests: The electric field as minus the potential gradient.

Show solution
  1. E=−dVdXE = -\dfrac{dV}{dX}: minus the slope of the V-X graph. Each straight piece gives a constant E.
  2. 0 to 2: V rises, slope positive, so E is negative (constant). 2 to 4: V constant, E = 0. 4 to 6: V falls, slope negative, so E is positive. The two slopes have the same size (same rise over the same distance), so the two values are equal and opposite: graph (i).

    Why: The stem says 'magnitude', but the options plot E with its sign; the key follows E = −dV/dX.

Answer(A) graph (i)
Ask about this question
Q16

Question 16 (1 mark)

Chapter 14: Semiconductor Electronics: Materials, Devices and Simple Circuits
Assertion (A): The electrical conductivity of a semiconductor increases on doping. \nReason (R): Doping always increases the number of electrons in the semiconductor.
  1. (A)Both A and R are true and R is the correct explanation of A
  2. (B)Both A and R are true and R is NOT the correct explanation of A
  3. (C)A is true but R is false
  4. (D)A is false and R is also false

Tests: n-type and p-type doping and the conductivity of extrinsic semiconductors.

Show solution
  1. A is true: doping adds a large number of charge carriers (electrons or holes), far more than the intrinsic ones, so the conductivity rises.
  2. R is false: a trivalent (acceptor) dopant gives a p-type semiconductor, which has more holes and fewer free electrons than the pure crystal. Doping does not always add electrons.
Answer(C) A is true but R is false
Ask about this question
Q17

Question 17 (1 mark)

Chapter 10: Wave Optics
Assertion (A): In an interference pattern observed in Young's double slit experiment, if the separation (d) between coherent sources as well as the distance (D) of the screen from the coherent sources both are reduced to 1/3rd, then new fringe width remains the same. \nReason (R): Fringe width is proportional to (d/D).
  1. (A)Both A and R are true and R is the correct explanation of A
  2. (B)Both A and R are true and R is NOT the correct explanation of A
  3. (C)A is true but R is false
  4. (D)A is false and R is also false

Tests: Fringe width in Young's double slit experiment.

Show solution
  1. Fringe width β=λDd\beta = \dfrac{\lambda D}{d}. With D→D3D \to \dfrac{D}{3} and d→d3d \to \dfrac{d}{3}: β′=λ(D/3)d/3=β\beta' = \dfrac{\lambda (D/3)}{d/3} = \beta. A is true.
  2. R is false: β\beta is proportional to Dd\dfrac{D}{d}, not dD\dfrac{d}{D}. (A follows from the correct formula, and would follow from R's too, but R is still a false statement.)
Answer(C) A is true but R is false
Ask about this question
Q18

Question 18 (1 mark)

Chapter 11: Dual Nature of Radiation and Matter
Assertion (A): The photoelectrons produced by a monochromatic light beam incident on a metal surface have a spread in their kinetic energies. \nReason (R): The energy of electrons emitted from inside the metal surface, is lost in collision with the other atoms in the metal.
  1. (A)Both A and R are true and R is the correct explanation of A
  2. (B)Both A and R are true and R is NOT the correct explanation of A
  3. (C)A is true but R is false
  4. (D)A is false and R is also false

Tests: Why photoelectrons have a range of kinetic energies up to Kmax.

Show solution
  1. A is true: each photon brings the same energy hνh\nu, but the emitted electrons have kinetic energies from zero up to Kmax=hν−ϕ0K_{max} = h\nu - \phi_0.
  2. R is true and explains A: only electrons from the very surface leave with KmaxK_{max}; electrons from deeper inside lose part of their energy in collisions on the way out (and some are more tightly bound), so they come out slower.
Answer(A) Both A and R are true and R is the correct explanation of A
Ask about this question

Section B: 7 questions of 2 marks each

Q19

Question 19 (2 marks)

Chapter 8: Electromagnetic Waves
Electromagnetic waves with wavelength (i) λ₁ is suitable for radar systems used in aircraft navigation. (ii) λ₂ is used to kill germs in water purifiers. (iii) λ₃ is used to improve visibility in runways during fog and mist conditions. Identify and name the part of the electromagnetic spectrum to which these radiations belong. Also arrange these wavelengths in ascending order of their magnitude.

Tests: Bands of the electromagnetic spectrum and their uses.

Show solution
  1. λ₁, radar: microwaves (wavelength about 1 mm to 0.3 m).
  2. λ₂, killing germs in water purifiers: ultraviolet rays (about 400 nm down to 1 nm).
  3. λ₃, seeing through fog and mist: infrared waves (about 1 mm to 700 nm), which are scattered far less than visible light by fog droplets.
  4. Ascending order of wavelength: ultraviolet < infrared < microwave, that is λ₂ < λ₃ < λ₁.
Answerλ₁ microwave, λ₂ ultraviolet, λ₃ infrared; λ₂ < λ₃ < λ₁
Ask about this question
Q20

Question 20 (2 marks)

Chapter 5: Magnetism and Matter
A uniform magnetic field gets modified as shown in figure when two specimens A and B are placed in it. (Figure (a): the field lines bend around specimen A, spreading away from it, with fewer lines passing through it. Figure (b): the field lines bend slightly towards specimen B, so a few more lines pass through it.) (i) Identify the specimen A and B. (ii) How is the magnetic susceptibility of specimen A different from that of specimen B?

    Tests: Field lines in dia- and paramagnetic materials and the sign of the susceptibility.

    Show solution

    (i)

    1. A pushes the field lines out of itself (the field inside is weaker than outside): A is diamagnetic.
    2. B draws a few more field lines into itself (the field inside is slightly stronger): B is paramagnetic. (A ferromagnet would crowd the lines in very strongly.)
    AnswerA diamagnetic, B paramagnetic

    (ii)

    1. A (diamagnetic): susceptibility small and negative, −1≤χ<0-1 \le \chi < 0. B (paramagnetic): small and positive, 0<χ≪10 < \chi \ll 1.
    Answerχ of A is small and negative; χ of B is small and positive
    Ask about this question
    Q21

    Question 21 (2 marks)

    Chapter 13: Nuclei
    Attempt either option (I) or (II).
    1. (I)
      What is the nuclear radius of 125Fe^{125}\mathrm{Fe}, if that of 27Al^{27}\mathrm{Al} is 3.6 fermi?
    2. (II)
      OR: The short wavelength limit for the Lyman series of the hydrogen spectrum is 913.4 Å. Calculate the short wavelength limit for the Balmer series of the hydrogen spectrum.

    Tests: Nuclear radius and mass number; series limits of the hydrogen spectrum.

    Show solution

    (I) What is the nuclear radius of 125Fe^{125}\mathrm{Fe}, if that of 27Al^{27}\mathrm{Al} is 3.6 fermi?

    1. R=R0A1/3R = R_0A^{1/3}, so RFeRAl=(AFeAAl)1/3=(12527)1/3=53\dfrac{R_{Fe}}{R_{Al}} = \left(\dfrac{A_{Fe}}{A_{Al}}\right)^{1/3} = \left(\dfrac{125}{27}\right)^{1/3} = \dfrac{5}{3}.
    2. RFe=53×3.6=6R_{Fe} = \dfrac{5}{3} \times 3.6 = 6 fermi.

      Why: Real iron nuclei have A = 54 to 58; the paper's 125 is taken as given (its cube root is 5).

    Answer6 fermi

    (II) OR: The short wavelength limit for the Lyman series of the hydrogen spectrum is 913.4 Å. Calculate the short wavelength limit for the Balmer series of the hydrogen spectrum.

    1. Short wavelength (series) limit: the transition from n=∞n = \infty. Lyman (n1=1n_1 = 1): 1λL=R(112−0)=R\dfrac{1}{\lambda_L} = R\left(\dfrac{1}{1^2} - 0\right) = R, so 1R=913.4\dfrac{1}{R} = 913.4 Å.
    2. Balmer (n1=2n_1 = 2): 1λB=R(122−0)=R4\dfrac{1}{\lambda_B} = R\left(\dfrac{1}{2^2} - 0\right) = \dfrac{R}{4}, so λB=4R=4×913.4=3653.6\lambda_B = \dfrac{4}{R} = 4 \times 913.4 = 3653.6 Å.
    Answer3653.6 Å
    Ask about this question
    Q22

    Question 22 (2 marks)

    Chapter 9: Ray Optics and Optical Instruments
    A biconvex lens made of a transparent material of refractive index 1.25 is immersed in water of refractive index 1.33. Will the lens behave as a converging or a diverging lens? Justify your answer.

    Tests: Lens maker's formula: a lens in a medium denser than itself.

    Show solution
    1. Lens maker's formula in a medium: 1f=(μmμw−1)(1R1−1R2)\dfrac{1}{f} = \left(\dfrac{\mu_m}{\mu_w} - 1\right)\left(\dfrac{1}{R_1} - \dfrac{1}{R_2}\right).
    2. For a biconvex lens 1R1−1R2>0\dfrac{1}{R_1} - \dfrac{1}{R_2} > 0. Here μmμw=1.251.33≈0.94\dfrac{\mu_m}{\mu_w} = \dfrac{1.25}{1.33} \approx 0.94, so μmμw−1<0\dfrac{\mu_m}{\mu_w} - 1 < 0.

      Why: The marking scheme writes this ratio as 0.98; it is 0.94. Either way it is less than 1.

    3. So f is negative: the lens, placed in a denser medium than its own material, behaves as a diverging lens.
    AnswerDiverging (f < 0, since 1.25/1.33 < 1)
    Ask about this question
    Q23

    Question 23 (2 marks)

    Chapter 14: Semiconductor Electronics: Materials, Devices and Simple Circuits
    Attempt either option (I) or (II).
    1. (I)
      The figure shows a piece of pure semiconductor S in series with a variable resistor R and a source of constant voltage V. Should the value of R be increased or decreased to keep the reading of the ammeter constant, when semiconductor S is heated? Justify your answer. (Figure: a single loop with S, the ammeter A, the cell V and the rheostat R in series.)
    2. (II)
      OR: The graph of potential barrier versus width of depletion region for an unbiased diode is shown in graph A. In comparison to A, graphs B and C are obtained after biasing the diode in different ways. Identify the type of biasing in B and C and justify your answer. (Graphs of V(x) against x: in A the potential rises along a sloping part (the depletion region) to a level and stays there; in B it rises to a clearly higher level; in C it rises only to a lower level.)

    Tests: Temperature and the resistance of an intrinsic semiconductor; the barrier potential under forward and reverse bias.

    Show solution

    (I) The figure shows a piece of pure semiconductor S in series with a variable resistor R and a source of constant voltage V. Should the value of R be increased or decreased to keep the reading of the ammeter constant, when semiconductor S is heated? Justify your answer. (Figure: a single loop with S, the ammeter A, the cell V and the rheostat R in series.)

    1. Heating a pure (intrinsic) semiconductor breaks more covalent bonds and creates more electron-hole pairs, so its resistance decreases.
    2. With V fixed, I=VRS+RI = \dfrac{V}{R_S + R} would rise. To keep the current constant, R must be increased by the amount RSR_S fell.
    AnswerIncrease R: the semiconductor's resistance falls on heating

    (II) OR: The graph of potential barrier versus width of depletion region for an unbiased diode is shown in graph A. In comparison to A, graphs B and C are obtained after biasing the diode in different ways. Identify the type of biasing in B and C and justify your answer. (Graphs of V(x) against x: in A the potential rises along a sloping part (the depletion region) to a level and stays there; in B it rises to a clearly higher level; in C it rises only to a lower level.)

    1. B: the barrier is higher than in A, so the diode is reverse biased. The battery raises the potential of the n side further, adding to the barrier (and widening the depletion region).
    2. C: the barrier is lower than in A, so the diode is forward biased. The battery raises the potential of the p side, opposing the barrier, so its height falls (and the depletion region narrows).
    AnswerB reverse biased (barrier higher); C forward biased (barrier lower)
    Ask about this question
    Q24

    Question 24 (2 marks)

    Chapter 10: Wave Optics
    A narrow slit is illuminated by a parallel beam of monochromatic light of wavelength λ equal to 6000 Å and the angular width of the central maximum in the resulting diffraction pattern is measured. When the slit is next illuminated by light of wavelength λ’, the angular width decreases by 30%. Calculate the value of the wavelength λ’.

    Tests: Width of the central maximum in single-slit diffraction.

    Show solution
    1. Angular width of the central maximum: 2θ=2λa2\theta = \dfrac{2\lambda}{a}, where a is the slit width. For the same slit it is proportional to λ\lambda.
    2. A 30% decrease means the new width is 0.70 of the old: 2λ′a=0.70×2λa\dfrac{2\lambda'}{a} = 0.70 \times \dfrac{2\lambda}{a}.
    3. λ′=0.70×6000=4200\lambda' = 0.70 \times 6000 = 4200 Å.
    Answerλ′ = 4200 Å
    Ask about this question
    Q25

    Question 25 (2 marks)

    Chapter 1: Electric Charges and Fields
    Two large, thin metal plates are parallel and close to each other. On their inner faces, the plates have surface charge densities of opposite signs and of magnitude 17.7×10−2217.7 \times 10^{-22} C/m². What is electric field intensity E: (a) in the outer region of the first plate, and (b) between the plates?

      Tests: Field of two oppositely charged parallel plates (Gauss's law for a charged sheet).

      Show solution

      (a)

      1. Each charged sheet gives a field σ2ε0\dfrac{\sigma}{2\varepsilon_0} pointing away from + and towards −. Outside the plates the fields of +σ+\sigma and −σ-\sigma are equal and opposite.
      2. So in the outer region of either plate E = 0.
      AnswerE = 0

      (b)

      1. Between the plates the two fields add: E=σε0E = \dfrac{\sigma}{\varepsilon_0}, from the positive plate to the negative one.
      2. E=17.7×10−228.85×10−12=2.0×10−10E = \dfrac{17.7 \times 10^{-22}}{8.85 \times 10^{-12}} = 2.0 \times 10^{-10} N/C.
      AnswerE=2.0×10−10E = 2.0 \times 10^{-10} N/C
      Ask about this question

      Section C: 5 questions of 3 marks each

      Q26

      Question 26 (3 marks)

      Chapter 4: Moving Charges and Magnetism
      Two long straight parallel conductors carrying currents I1I_1 and I2I_2 are separated by a distance d. If the currents are flowing in the same direction, show how the magnetic field produced by one exerts an attractive force on the other. Obtain the expression for this force and hence define 1 ampere.

      Tests: Force between parallel currents and the definition of the ampere.

      Show solution
      1. Diagram: two long vertical wires a and b, a distance d apart, both carrying current upwards (I1I_1 in a, I2I_2 in b). The field BaB_a of wire a at wire b is perpendicular to b, into the page (right-hand rule).
      2. Ampère's law: Ba=μ0I12πdB_a = \dfrac{\mu_0 I_1}{2\pi d}, the same all along wire b.
      3. Force on a length L of b: Fba=I2LBa=μ0I1I2L2πdF_{ba} = I_2 L B_a = \dfrac{\mu_0 I_1 I_2 L}{2\pi d}. By F⃗=I2L⃗×B⃗a\vec F = I_2\vec L \times \vec B_a (or Fleming's left-hand rule) it points towards a. Likewise b's field pushes a towards b: equal and opposite forces, so the wires attract.
      4. Force per unit length: f=μ0I1I22πdf = \dfrac{\mu_0 I_1 I_2}{2\pi d}. With I1=I2=1I_1 = I_2 = 1 A and d=1d = 1 m: f=4π×10−72π=2×10−7f = \dfrac{4\pi \times 10^{-7}}{2\pi} = 2 \times 10^{-7} N/m.
      5. One ampere is the steady current which, maintained in each of two very long, straight, parallel conductors of negligible cross-section placed one metre apart in vacuum, produces on each a force of 2×10−72 \times 10^{-7} N per metre of length.

        Why: This is the NCERT definition; since 2019 the SI fixes the ampere through the elementary charge, with the same value.

      AnswerFL=μ0I1I22πd\dfrac{F}{L} = \dfrac{\mu_0 I_1 I_2}{2\pi d} (attractive); 1 A gives 2×10−72 \times 10^{-7} N/m at 1 m
      Ask about this question
      Q27

      Question 27 (3 marks)

      Chapter 6: Electromagnetic Induction
      The magnetic field through a circular loop of wire, 12cm in radius and 8.5Ω resistance, changes with time as shown in the figure. The magnetic field is perpendicular to the plane of the loop. Calculate the current induced in the loop and plot a graph showing induced current as a function of time. (Figure: B rises linearly from 0 at t = 0 to 1 T at t = 2 s, stays at 1 T until t = 4 s, and falls linearly to 0 at t = 6 s.)

      Tests: Faraday's law: induced emf from the slope of a B-t graph.

      Show solution
      1. Area: A=πr2=3.14×(0.12)2=4.52×10−2A = \pi r^2 = 3.14 \times (0.12)^2 = 4.52 \times 10^{-2} m². Induced emf ε=−dΦdt=−AdBdt\varepsilon = -\dfrac{d\Phi}{dt} = -A\dfrac{dB}{dt}.
      2. 0 < t < 2 s: dBdt=1−02=0.5\dfrac{dB}{dt} = \dfrac{1 - 0}{2} = 0.5 T/s, ε1=−4.52×10−2×0.5=−2.26×10−2\varepsilon_1 = -4.52 \times 10^{-2} \times 0.5 = -2.26 \times 10^{-2} V, I1=ε1R=−2.26×10−28.5=−2.66×10−3I_1 = \dfrac{\varepsilon_1}{R} = \dfrac{-2.26 \times 10^{-2}}{8.5} = -2.66 \times 10^{-3} A.
      3. 2 s < t < 4 s: B is constant, so ε2=0\varepsilon_2 = 0 and I2=0I_2 = 0.
      4. 4 s < t < 6 s: dBdt=0−12=−0.5\dfrac{dB}{dt} = \dfrac{0 - 1}{2} = -0.5 T/s, so ε3=+2.26×10−2\varepsilon_3 = +2.26 \times 10^{-2} V and I3=+2.66×10−3I_3 = +2.66 \times 10^{-3} A, opposite in sense to I1I_1.

        Why: The marking scheme rounds the area to 4.5 × 10⁻² m² and writes 2.6 mA; with the area unrounded the current is 2.66 mA (about 2.7 mA).

      5. Graph of I (mA) against t (s): a horizontal line at −2.66 from 0 to 2 s, zero from 2 to 4 s, and a horizontal line at +2.66 from 4 to 6 s (a rectangular step down, then a step up).
      Answer|I| ≈ 2.66 mA for 0-2 s and 4-6 s (opposite senses), zero for 2-4 s
      Ask about this question
      Q28

      Question 28 (3 marks)

      Chapter 7: Alternating Current
      Attempt either option (I) or (II).
      1. (I)
        An a.c. source generating a voltage ε=ε0sin⁡ωt\varepsilon = \varepsilon_0\sin\omega t is connected to a capacitor of capacitance C. Find the expression for the current I flowing through it. Plot a graph of ε\varepsilon and I versus ωt\omega t to show that the current is ahead of the voltage by π/2\pi/2.
      2. (II)
        OR: An ac voltage V=V0sin⁡ωtV = V_0\sin\omega t is applied across a pure inductor of inductance L. Find an expression for the current i, flowing in the circuit and show mathematically that the current flowing through it lags behind the applied voltage by a phase angle of π2\dfrac{\pi}{2}. Also draw graphs of V and i versus ωt\omega t for the circuit.

      Tests: Current and phase in a purely capacitive and a purely inductive ac circuit.

      Show solution

      (I) An a.c. source generating a voltage ε=ε0sin⁡ωt\varepsilon = \varepsilon_0\sin\omega t is connected to a capacitor of capacitance C. Find the expression for the current I flowing through it. Plot a graph of ε\varepsilon and I versus ωt\omega t to show that the current is ahead of the voltage by π/2\pi/2.

      1. At every instant the capacitor's voltage equals the source's: qC=ε0sin⁡ωt\dfrac{q}{C} = \varepsilon_0\sin\omega t, so q=Cε0sin⁡ωtq = C\varepsilon_0\sin\omega t.
      2. I=dqdt=ωCε0cos⁡ωt=I0sin⁡(ωt+π2)I = \dfrac{dq}{dt} = \omega C\varepsilon_0\cos\omega t = I_0\sin\left(\omega t + \dfrac{\pi}{2}\right), with I0=ε01/ωC=ε0XCI_0 = \dfrac{\varepsilon_0}{1/\omega C} = \dfrac{\varepsilon_0}{X_C}.
      3. So the current leads the voltage by π2\dfrac{\pi}{2}.
      4. Graph against ωt\omega t: ε\varepsilon is a sine curve starting at 0 and peaking (ε0\varepsilon_0) at π/2\pi/2; I is a cosine curve starting at its peak I0I_0 at 0, zero at π/2\pi/2, −I0-I_0 at π\pi. Each value of I comes a quarter cycle before the same value of ε\varepsilon.
      AnswerI=ε0XCsin⁡(ωt+π2)I = \dfrac{\varepsilon_0}{X_C}\sin\left(\omega t + \dfrac{\pi}{2}\right), XC=1ωCX_C = \dfrac{1}{\omega C}: I leads by π/2\pi/2

      (II) OR: An ac voltage V=V0sin⁡ωtV = V_0\sin\omega t is applied across a pure inductor of inductance L. Find an expression for the current i, flowing in the circuit and show mathematically that the current flowing through it lags behind the applied voltage by a phase angle of π2\dfrac{\pi}{2}. Also draw graphs of V and i versus ωt\omega t for the circuit.

      1. The source voltage balances the back emf of the inductor (no resistance): V0sin⁡ωt=LdidtV_0\sin\omega t = L\dfrac{di}{dt}, so didt=V0Lsin⁡ωt\dfrac{di}{dt} = \dfrac{V_0}{L}\sin\omega t.
      2. Integrating: i=−V0ωLcos⁡ωt=i0sin⁡(ωt−π2)i = -\dfrac{V_0}{\omega L}\cos\omega t = i_0\sin\left(\omega t - \dfrac{\pi}{2}\right), with i0=V0ωL=V0XLi_0 = \dfrac{V_0}{\omega L} = \dfrac{V_0}{X_L} (the constant of integration is zero, since the current has no steady part).
      3. So the current lags the voltage by π2\dfrac{\pi}{2}.
      4. Graph against ωt\omega t: V is a sine curve, peak V0V_0 at π/2\pi/2; i starts at −i0-i_0 at 0, is zero at π/2\pi/2 and peaks (i0i_0) at π\pi. Each value of i comes a quarter cycle after the same value of V.
      Answeri=V0ωLsin⁡(ωt−π2)i = \dfrac{V_0}{\omega L}\sin\left(\omega t - \dfrac{\pi}{2}\right): i lags V by π/2\pi/2
      Ask about this question
      Q29

      Question 29 (3 marks)

      Chapter 11: Dual Nature of Radiation and Matter
      Attempt either option (I) or (II).
      1. (I)
        Radiation of frequency 10¹⁵ Hz is incident on three photosensitive surfaces A, B and C. Following observations are recorded: Surface A: no photoemission occurs. Surface B: photoemission occurs but the photoelectrons have zero kinetic energy. Surface C: photo emission occurs and photoelectrons have some kinetic energy. Using Einstein’s photo-electric equation, explain the three observations.
      2. (II)(a)
        OR: The graph shows the variation of photocurrent for a photosensitive metal. (Graph: photocurrent against a horizontal axis through O; the current is zero at a point A to the left of O, rises through O and levels off to a constant value towards X on the right.) (a) What does X and A on the horizontal axis represent?
      3. (II)(b)
        (b) Draw this graph for three different values of frequencies of incident radiation υ₁, υ₂ and υ₃ (υ₃ > υ₂ > υ₁) for the same intensity.
      4. (II)(c)
        (c) Draw this graph for three different values of intensities of incident radiation I₁, I₂ and I₃ (I₃ > I₂ > I₁) having the same frequency.

      Tests: Einstein's photoelectric equation and the photocurrent-voltage graphs for different frequencies and intensities.

      Show solution

      (I) Radiation of frequency 10¹⁵ Hz is incident on three photosensitive surfaces A, B and C. Following observations are recorded: Surface A: no photoemission occurs. Surface B: photoemission occurs but the photoelectrons have zero kinetic energy. Surface C: photo emission occurs and photoelectrons have some kinetic energy. Using Einstein’s photo-electric equation, explain the three observations.

      1. Einstein's equation: Kmax=hν−ϕ0=h(ν−ν0)K_{max} = h\nu - \phi_0 = h(\nu - \nu_0), where ν0=ϕ0h\nu_0 = \dfrac{\phi_0}{h} is the threshold frequency of the surface.
      2. A: ν0>1015\nu_0 > 10^{15} Hz. A photon's energy hνh\nu is less than the work function, so no electron can escape: no emission.
      3. B: ν0=1015\nu_0 = 10^{15} Hz. The photon's energy just equals the work function, so electrons are emitted with Kmax=0K_{max} = 0.
      4. C: ν0<1015\nu_0 < 10^{15} Hz. The photon's energy exceeds the work function, and the excess, h(ν−ν0)h(\nu - \nu_0), appears as kinetic energy.
      Answerν₀(A) > 10¹⁵ Hz; ν₀(B) = 10¹⁵ Hz; ν₀(C) < 10¹⁵ Hz

      (II)(a) OR: The graph shows the variation of photocurrent for a photosensitive metal. (Graph: photocurrent against a horizontal axis through O; the current is zero at a point A to the left of O, rises through O and levels off to a constant value towards X on the right.) (a) What does X and A on the horizontal axis represent?

      1. The horizontal axis is the potential of the collector (anode) relative to the emitter. X: the collector (anode) potential, positive to the right of O.
      2. A: the stopping (cut-off) potential, the negative collector potential at which the photocurrent just becomes zero.
      AnswerX: anode (collector) potential; A: stopping potential

      (II)(b) (b) Draw this graph for three different values of frequencies of incident radiation υ₁, υ₂ and υ₃ (υ₃ > υ₂ > υ₁) for the same intensity.

      1. Three curves that merge into the same saturation current on the right (same intensity, so the same number of photoelectrons per second).
      2. On the left they cut the axis at different stopping potentials: the higher the frequency, the more negative: −V₀₃ (for υ₃) furthest left, then −V₀₂, then −V₀₁ nearest O.

        Why: eV₀ = hυ − φ₀ grows with frequency.

      AnswerSame saturation current; stopping potential larger for higher frequency

      (II)(c) (c) Draw this graph for three different values of intensities of incident radiation I₁, I₂ and I₃ (I₃ > I₂ > I₁) having the same frequency.

      1. Three curves that all start from the same stopping potential −V₀ on the axis (same frequency, so the same maximum kinetic energy).
      2. They level off at different saturation currents, proportional to the intensity: the I₃ curve highest, then I₂, then I₁.
      AnswerSame stopping potential; saturation current I₃ > I₂ > I₁
      Ask about this question
      Q30

      Question 30 (3 marks)

      Chapter 11: Dual Nature of Radiation and Matter
      The ground state energy of hydrogen atom is -13.6 eV. The photon emitted during the transition of electron from n=3 to n=1 state, is incident on a photosensitive material of unknown work function. The photoelectrons are emitted from the material with the maximum kinetic energy of 9eV. Calculate the threshold wavelength of the material used.

      Tests: Bohr energy levels feeding Einstein's photoelectric equation.

      Show solution
      1. En=−13.6n2E_n = -\dfrac{13.6}{n^2} eV. Photon energy: hν=E3−E1=13.6(112−132)=13.6×89=12.09≈12.1h\nu = E_3 - E_1 = 13.6\left(\dfrac{1}{1^2} - \dfrac{1}{3^2}\right) = 13.6 \times \dfrac{8}{9} = 12.09 \approx 12.1 eV.
      2. Einstein's equation: W0=hν−Kmax=12.09−9=3.09≈3.1W_0 = h\nu - K_{max} = 12.09 - 9 = 3.09 \approx 3.1 eV.
      3. λth=hcW0=6.62×10−34×3×1083.1×1.6×10−19≈4.0×10−7\lambda_{th} = \dfrac{hc}{W_0} = \dfrac{6.62 \times 10^{-34} \times 3 \times 10^8}{3.1 \times 1.6 \times 10^{-19}} \approx 4.0 \times 10^{-7} m (400 nm).
      Answerλth≈4×10−7\lambda_{th} \approx 4 \times 10^{-7} m
      Ask about this question

      Section D: 3 long questions of 5 marks each

      Q31

      Question 31 (5 marks)

      Chapter 2: Electrostatic Potential and Capacitance
      Attempt either option (I) or (II).
      1. (I)(a)
        Draw equipotential surfaces for (i) an electric dipole and (ii) two identical positive charges placed near each other.
      2. (I)(b)(i)
        In a parallel plate capacitor with air between the plates, each plate has an area of 6×10−36 \times 10^{-3} m² and the separation between the plates is 3 mm. (i) Calculate the capacitance of the capacitor.
      3. (I)(b)(ii)
        (ii) If the capacitor is connected to 100V supply, what would be the charge on each plate?
      4. (I)(b)(iii)
        (iii) How would charge on the plate be affected if a 3 mm thick mica sheet of k=6 is inserted between the plates while the voltage supply remains connected?
      5. (II)(a)
        OR: Three charges –q, Q and –q are placed at equal distances on a straight line. If the potential energy of the system of these charges is zero, then what is the ratio Q:q?
      6. (II)(b)(i)
        (b)(i) Obtain the expression for the electric field intensity due to a uniformly charged spherical shell of radius R at a point distant r from the centre of the shell outside it.
      7. (II)(b)(ii)
        (ii) Draw a graph showing the variation of electric field intensity E with r, for r > R and r < R.

      Tests: Equipotential surfaces and the parallel plate capacitor with a dielectric; potential energy of charges and Gauss's law for a shell.

      Show solution

      (I)(a) Draw equipotential surfaces for (i) an electric dipole and (ii) two identical positive charges placed near each other.

      1. (i) Dipole: close to each charge the equipotentials are small closed surfaces (nearly spheres) around it, positive potentials around +q and negative around −q. Further out they are stretched and flattened towards the middle. The plane bisecting the dipole at right angles is the equipotential V = 0. Field lines, from +q to −q, cross every surface at right angles.
      2. (ii) Two identical positive charges: near each charge, nearly spherical surfaces around it. At lower potentials (further out) the surfaces bulge towards each other and join into a figure-of-eight shape through the midpoint (where E = 0), and far away they become single, nearly spherical surfaces enclosing both charges.

        Why: The scheme's sketch shows only the circles around each charge; the zero plane and the joined surfaces complete the picture.

      AnswerDipole: closed surfaces round each charge with the bisecting plane at V = 0; two + charges: surfaces round each, merging into ones enclosing both

      (I)(b)(i) In a parallel plate capacitor with air between the plates, each plate has an area of 6×10−36 \times 10^{-3} m² and the separation between the plates is 3 mm. (i) Calculate the capacitance of the capacitor.

      1. C=ε0Ad=8.85×10−12×6×10−33×10−3=17.7×10−12C = \dfrac{\varepsilon_0 A}{d} = \dfrac{8.85 \times 10^{-12} \times 6 \times 10^{-3}}{3 \times 10^{-3}} = 17.7 \times 10^{-12} F =17.7= 17.7 pF.
      AnswerC = 17.7 pF

      (I)(b)(ii) (ii) If the capacitor is connected to 100V supply, what would be the charge on each plate?

      1. Q=CV=17.7×10−12×100=1.77×10−9Q = CV = 17.7 \times 10^{-12} \times 100 = 1.77 \times 10^{-9} C: +1.77×10−9+1.77 \times 10^{-9} C on one plate and −1.77×10−9-1.77 \times 10^{-9} C on the other.
      AnswerQ=1.77×10−9Q = 1.77 \times 10^{-9} C

      (I)(b)(iii) (iii) How would charge on the plate be affected if a 3 mm thick mica sheet of k=6 is inserted between the plates while the voltage supply remains connected?

      1. The 3 mm sheet fills the whole gap, so the capacitance becomes C′=kC=6×17.7=106.2C' = kC = 6 \times 17.7 = 106.2 pF.
      2. The supply keeps V = 100 V, so Q′=C′V=106.2×10−12×100=1.062×10−8Q' = C'V = 106.2 \times 10^{-12} \times 100 = 1.062 \times 10^{-8} C: the charge becomes 6 times as large (extra charge flows from the supply).
      AnswerQ′=1.062×10−8Q' = 1.062 \times 10^{-8} C (6 times larger)

      (II)(a) OR: Three charges –q, Q and –q are placed at equal distances on a straight line. If the potential energy of the system of these charges is zero, then what is the ratio Q:q?

      1. Let the spacing be x, with −q-q, Q, −q-q in that order. Three pairs: two at distance x, one (−q-q and −q-q) at 2x.
      2. U=k[(−q)Qx+Q(−q)x+(−q)(−q)2x]=0U = k\left[\dfrac{(-q)Q}{x} + \dfrac{Q(-q)}{x} + \dfrac{(-q)(-q)}{2x}\right] = 0, so 2qQx=q22x\dfrac{2qQ}{x} = \dfrac{q^2}{2x}.
      3. Q=q4Q = \dfrac{q}{4}: Q:q=1:4Q : q = 1 : 4.
      AnswerQ : q = 1 : 4

      (II)(b)(i) (b)(i) Obtain the expression for the electric field intensity due to a uniformly charged spherical shell of radius R at a point distant r from the centre of the shell outside it.

      1. Diagram: the shell of radius R, centre O, total charge q; P at distance r > R. Take as the Gaussian surface a sphere of radius r centred on O, through P.
      2. By symmetry E⃗\vec E is radial and has the same magnitude everywhere on this sphere, so ∮E⃗⋅dS⃗=E×4πr2\oint \vec E \cdot d\vec S = E \times 4\pi r^2.
      3. The Gaussian sphere encloses the whole charge q. Gauss's law: E×4πr2=qε0E \times 4\pi r^2 = \dfrac{q}{\varepsilon_0}, so E=14πε0qr2E = \dfrac{1}{4\pi\varepsilon_0}\dfrac{q}{r^2} (r>Rr > R): as if all the charge were at the centre.
      AnswerE=14πε0qr2E = \dfrac{1}{4\pi\varepsilon_0}\dfrac{q}{r^2} for r>Rr > R

      (II)(b)(ii) (ii) Draw a graph showing the variation of electric field intensity E with r, for r > R and r < R.

      1. Inside (r<Rr < R), a Gaussian sphere encloses no charge, so E=0E = 0.
      2. Graph: E is zero along the r axis from 0 to R, jumps to its largest value q4πε0R2\dfrac{q}{4\pi\varepsilon_0R^2} at r=Rr = R, then falls as 1r2\dfrac{1}{r^2} outside.

        Why: The scheme's graph draws a dashed line at that value for r < R; it only marks the level reached at r = R. The field inside is zero.

      AnswerE = 0 for r < R; E ∝ 1/r² for r > R, largest just outside the surface
      Ask about this question
      Q32

      Question 32 (5 marks)

      Chapter 3: Current Electricity
      Attempt either option (I) or (II).
      1. (I)(a)
        Explain the term drift velocity of electrons in a conductor. Hence obtain the expression for the current through a conductor in terms of drift velocity.
      2. (I)(b)
        Two cells of emfs E1E_1 and E2E_2 and internal resistances r1r_1 and r2r_2 respectively are connected in parallel as shown in the figure. Deduce the expression for the (i) equivalent emf of the combination (ii) equivalent internal resistance of the combination (iii) potential difference between the points A and B. (Figure: the two cells on the upper and lower arms of a diamond, with their positive plates on the A side; a current I enters the combination from B and leaves towards A.)
      3. (II)(a)
        OR: State the two Kirchhoff’s rules used in the analysis of electric circuits and explain them.
      4. (II)(b)
        (b) Derive the equation of the balanced state in a Wheatstone bridge using Kirchhoff’s laws.

      Tests: Drift velocity and current; cells in parallel; Kirchhoff's rules and the Wheatstone bridge.

      Show solution

      (I)(a) Explain the term drift velocity of electrons in a conductor. Hence obtain the expression for the current through a conductor in terms of drift velocity.

      1. Drift velocity: the average velocity that the free electrons acquire, superimposed on their random thermal motion, opposite to the applied electric field, along the length of the conductor.
      2. Each electron accelerates at eEm\dfrac{eE}{m} between collisions; averaged over the mean free time τ\tau: vd=eEτmv_d = \dfrac{eE\tau}{m}.
      3. Take a conductor of cross-section A with n free electrons per unit volume. In time Δt\Delta t every electron within a length vdΔtv_d\Delta t of a cross-section crosses it: that is nAvdΔtnAv_d\Delta t electrons, carrying charge Δq=neAvdΔt\Delta q = neAv_d\Delta t.
      4. I=ΔqΔt=neAvdI = \dfrac{\Delta q}{\Delta t} = neAv_d.
      AnswerI=neAvdI = neAv_d

      (I)(b) Two cells of emfs E1E_1 and E2E_2 and internal resistances r1r_1 and r2r_2 respectively are connected in parallel as shown in the figure. Deduce the expression for the (i) equivalent emf of the combination (ii) equivalent internal resistance of the combination (iii) potential difference between the points A and B. (Figure: the two cells on the upper and lower arms of a diamond, with their positive plates on the A side; a current I enters the combination from B and leaves towards A.)

      1. The current divides: I=I1+I2I = I_1 + I_2. Let V be the potential difference between A and B (the terminal voltage of each cell).
      2. For each cell, V=E1−I1r1V = E_1 - I_1r_1 and V=E2−I2r2V = E_2 - I_2r_2, so I1=E1−Vr1I_1 = \dfrac{E_1 - V}{r_1} and I2=E2−Vr2I_2 = \dfrac{E_2 - V}{r_2}.
      3. I=(E1r1+E2r2)−V(1r1+1r2)I = \left(\dfrac{E_1}{r_1} + \dfrac{E_2}{r_2}\right) - V\left(\dfrac{1}{r_1} + \dfrac{1}{r_2}\right), so V=E1r2+E2r1r1+r2−Ir1r2r1+r2V = \dfrac{E_1r_2 + E_2r_1}{r_1 + r_2} - I\dfrac{r_1r_2}{r_1 + r_2}.
      4. Compare with a single cell, V=Eeq−IreqV = E_{eq} - Ir_{eq}: (i) Eeq=E1r2+E2r1r1+r2E_{eq} = \dfrac{E_1r_2 + E_2r_1}{r_1 + r_2}, (ii) req=r1r2r1+r2r_{eq} = \dfrac{r_1r_2}{r_1 + r_2}, (iii) VAB=Eeq−IreqV_{AB} = E_{eq} - Ir_{eq}.
      AnswerEeq=E1r2+E2r1r1+r2E_{eq} = \dfrac{E_1r_2 + E_2r_1}{r_1 + r_2}, req=r1r2r1+r2r_{eq} = \dfrac{r_1r_2}{r_1 + r_2}, V=Eeq−IreqV = E_{eq} - Ir_{eq}

      (II)(a) OR: State the two Kirchhoff’s rules used in the analysis of electric circuits and explain them.

      1. Junction rule: at any junction, the sum of the currents entering equals the sum of the currents leaving. It follows from conservation of charge: charge cannot pile up at a junction in a steady state.
      2. Loop rule: the algebraic sum of the changes in potential around any closed loop (across resistors and cells) is zero. It follows from conservation of energy: the electrostatic force is conservative, so a charge taken round a loop returns to the same potential.
      AnswerΣI = 0 at a junction (charge conservation); ΣΔV = 0 round a loop (energy conservation)

      (II)(b) (b) Derive the equation of the balanced state in a Wheatstone bridge using Kirchhoff’s laws.

      1. Diagram: four resistors P (arm AB), Q (arm BC), R (arm AD) and S (arm DC); a galvanometer G between B and D, and a cell between A and C. Currents: I1I_1 in AB, I2I_2 in AD, IgI_g in BD; then I1−IgI_1 - I_g in BC and I2+IgI_2 + I_g in DC (junction rule).
      2. Loop ABDA: I1P+IgG−I2R=0I_1P + I_gG - I_2R = 0.
      3. Loop BCDB: (I1−Ig)Q−(I2+Ig)S−IgG=0(I_1 - I_g)Q - (I_2 + I_g)S - I_gG = 0.
      4. Balanced bridge: Ig=0I_g = 0. Then I1P=I2RI_1P = I_2R and I1Q=I2SI_1Q = I_2S. Dividing: PQ=RS\dfrac{P}{Q} = \dfrac{R}{S}.
      AnswerBalance (Ig=0I_g = 0): PQ=RS\dfrac{P}{Q} = \dfrac{R}{S}
      Ask about this question
      Q33

      Question 33 (5 marks)

      Chapter 9: Ray Optics and Optical Instruments
      Attempt either option (I) or (II).
      1. (I)(a)
        Draw the graph showing intensity distribution of fringes with phase angle due to diffraction through a single slit. What is the width of the central maximum in comparison to that of a secondary maximum?
      2. (I)(b)
        A ray PQ is incident normally on the face AB of a triangular prism of refracting angle 60∘60^\circ as shown in figure. The prism is made of a transparent material of refractive index 23\dfrac{2}{\sqrt3}. Trace the path of the ray as it passes through the prism. Calculate the angle of emergence and the angle of deviation. (Figure: triangle ABC with apex A of angle 60° at the top; the ray PQ comes from the upper left and meets face AB at Q at right angles.)
      3. (II)(a)
        OR: Write two points of difference between an interference pattern and a diffraction pattern.
      4. (II)(b)(i)
        (b)(i) A ray of light incident on face AB of an equilateral glass prism, shows minimum deviation of 30°. Calculate the speed of light through the prism. (Figure: an equilateral triangle ABC, apex A at the top.)
      5. (II)(b)(ii)
        (ii) Find the angle of incidence at face AB so that the emergent ray grazes along the face AC.

      Tests: Refraction through a prism, critical angle and grazing emergence; single-slit diffraction compared with interference.

      Show solution

      (I)(a) Draw the graph showing intensity distribution of fringes with phase angle due to diffraction through a single slit. What is the width of the central maximum in comparison to that of a secondary maximum?

      1. Graph of intensity against the diffraction angle θ (or the phase angle): a tall central peak at θ = 0, zero intensity (minima) at θ = ±λ/a, ±2λ/a, ±3λ/a, ..., and between them much weaker secondary maxima (near ±3λ/2a, ±5λ/2a, ...) that get fainter further out.
      2. The central maximum runs from −λ/a to +λ/a (width 2λ/a); each secondary maximum runs between successive minima (width λ/a). So the central maximum is twice as wide as a secondary maximum.
      AnswerCentral maximum twice as wide as a secondary maximum

      (I)(b) A ray PQ is incident normally on the face AB of a triangular prism of refracting angle 60∘60^\circ as shown in figure. The prism is made of a transparent material of refractive index 23\dfrac{2}{\sqrt3}. Trace the path of the ray as it passes through the prism. Calculate the angle of emergence and the angle of deviation. (Figure: triangle ABC with apex A of angle 60° at the top; the ray PQ comes from the upper left and meets face AB at Q at right angles.)

      1. At Q the ray is along the normal (i=0i = 0), so it enters undeviated: r1=0r_1 = 0.
      2. r1+r2=Ar_1 + r_2 = A, so at face AC (point M) the angle of incidence is r2=60∘r_2 = 60^\circ.
      3. Critical angle: sin⁡C=1μ=32\sin C = \dfrac{1}{\mu} = \dfrac{\sqrt3}{2}, so C=60∘C = 60^\circ. The ray meets AC exactly at the critical angle, so it emerges grazing along the face AC: e=90∘e = 90^\circ.
      4. Deviation: δ=i+e−A=0+90∘−60∘=30∘\delta = i + e - A = 0 + 90^\circ - 60^\circ = 30^\circ.
      5. Ray trace: PQ enters AB at right angles, travels straight to M on AC, and leaves along the surface AC, towards C.
      Answere=90∘e = 90^\circ (grazes along AC), δ=30∘\delta = 30^\circ

      (II)(a) OR: Write two points of difference between an interference pattern and a diffraction pattern.

      1. 1. The interference pattern has many equally spaced bright and dark bands of (nearly) equal width; the diffraction pattern has a central bright maximum twice as wide as the other maxima.
      2. 2. In interference the bright fringes have (nearly) the same intensity; in diffraction the intensity falls off for successive maxima away from the centre.
      3. 3. Interference is the superposition of two waves from two narrow slits (two coherent sources); diffraction is the superposition of a continuous family of waves from every point of a single slit. (Any two.)
      AnswerEqual-width fringes vs central maximum twice as wide; equal intensities vs falling off

      (II)(b)(i) (b)(i) A ray of light incident on face AB of an equilateral glass prism, shows minimum deviation of 30°. Calculate the speed of light through the prism. (Figure: an equilateral triangle ABC, apex A at the top.)

      1. μ=sin⁡A+δm2sin⁡A2=sin⁡45∘sin⁡30∘=1/21/2=2\mu = \dfrac{\sin\frac{A + \delta_m}{2}}{\sin\frac{A}{2}} = \dfrac{\sin 45^\circ}{\sin 30^\circ} = \dfrac{1/\sqrt2}{1/2} = \sqrt2.
      2. v=cμ=3×1082≈2.12×108v = \dfrac{c}{\mu} = \dfrac{3 \times 10^8}{\sqrt2} \approx 2.12 \times 10^8 m/s.
      Answerμ=2\mu = \sqrt{2}, v≈2.12×108v \approx 2.12 \times 10^8 m/s

      (II)(b)(ii) (ii) Find the angle of incidence at face AB so that the emergent ray grazes along the face AC.

      1. Grazing emergence at AC (e=90∘e = 90^\circ) means the ray meets AC at the critical angle: sin⁡r2=1μ=12\sin r_2 = \dfrac{1}{\mu} = \dfrac{1}{\sqrt2}, r2=45∘r_2 = 45^\circ.
      2. r1=A−r2=60∘−45∘=15∘r_1 = A - r_2 = 60^\circ - 45^\circ = 15^\circ.
      3. At AB: sin⁡i=μsin⁡r1=2×sin⁡15∘=1.414×0.2588=0.366\sin i = \mu\sin r_1 = \sqrt2 \times \sin 15^\circ = 1.414 \times 0.2588 = 0.366, so i≈21.5∘i \approx 21.5^\circ.
      Answeri≈21.5∘i \approx 21.5^\circ
      Ask about this question

      Section E: 2 case study based questions of 4 marks each

      Q34

      Question 34 (4 marks)

      Chapter 9: Ray Optics and Optical Instruments
      Case Study. Read the following paragraph and answer the questions. A number of optical devices and instruments have been designed and developed such as periscope, binoculars, microscopes and telescopes utilising the reflecting and refracting properties of mirrors, lenses and prisms. Most of them are in common use. Our knowledge about the formation of images by the mirrors and lenses is the basic requirement for understanding the working of these devices.
      1. (i)
        Why the image formed at infinity is often considered most suitable for viewing. Explain
      2. (ii)
        In modern microscopes multicomponent lenses are used for both the objective and the eyepiece. Why?
      3. (iii)
        Write two points of difference between a compound microscope and an astronomical telescope
      4. (iii) OR
        OR: Write two distinct advantages of a reflecting type telescope over a refracting type telescope.

      Tests: Optical instruments: viewing an image at infinity, aberrations, the microscope and the telescope.

      Show solution

      (i) Why the image formed at infinity is often considered most suitable for viewing. Explain

      1. To see an object at infinity the eye is fully relaxed: the ciliary muscles do not have to squeeze the eye lens. So an image at infinity can be viewed for a long time with the least strain (the magnification is only slightly less than with the image at the near point).
      AnswerThe eye is relaxed (least strain on the ciliary muscles)

      (ii) In modern microscopes multicomponent lenses are used for both the objective and the eyepiece. Why?

      1. A single lens suffers from aberrations: chromatic (different colours focus at different points) and spherical (edge and central rays focus at different points). Combining several lenses of different glasses and shapes cancels these, so the image is sharper and free of coloured fringes.
      AnswerTo reduce chromatic and spherical aberrations (better image quality)

      (iii) Write two points of difference between a compound microscope and an astronomical telescope

      1. 1. Use: a compound microscope magnifies tiny objects close to it; an astronomical telescope gives angular magnification of distant objects.
      2. 2. Lenses: in the microscope the objective has a short focal length (shorter than the eyepiece's) and a small aperture; in the telescope the objective has a long focal length (much longer than the eyepiece's) and a large aperture.
      3. 3. Length: the microscope's tube length is fixed and much larger than the focal lengths; the telescope's length is about fo + fe. (Any two.)
      AnswerNear tiny objects vs distant objects; objective of short vs long focal length

      (iii) OR OR: Write two distinct advantages of a reflecting type telescope over a refracting type telescope.

      1. 1. A mirror has no chromatic aberration (reflection does not depend on wavelength), and a paraboloidal mirror has no spherical aberration either.
      2. 2. A mirror can be supported over its whole back, so it can be made very large without sagging, and it is cheaper and lighter than a lens of the same size. A large mirror gathers more light (a brighter image) and resolves finer detail.

        Why: The marking scheme lists 'more magnified' as an advantage; the magnification fo/fe is not a property of the reflecting design as such, so the page gives the standard advantages.

      AnswerNo chromatic (or spherical) aberration; large mirrors: brighter image and higher resolving power
      Ask about this question
      Q35

      Question 35 (4 marks)

      Case study: Light emitting diode. Read the following paragraph and answer the questions. LED is a heavily doped P-N junction which under forward bias emits spontaneous radiation. When it is forward biased, due to recombination of holes and electrons at the junction, energy is released in the form of photons. In the case of Si and Ge diode, the energy released in recombination lies in the infrared region. LEDs that can emit red, yellow, orange, green and blue light are commercially available. The semiconductor used for fabrication of visible LEDs must at least have a band gap of 1.8 eV. The compound semiconductor Gallium Arsenide – Phosphide is used for making LEDs of different colours. (Photograph: LEDs of different kinds, red, blue, green, yellow and white.)
      1. (i)
        Why are LEDs made of compound semiconductor and not of elemental semiconductors?
      2. (ii)
        What should be the order of bandgap of an LED, if it is required to emit light in the visible range?
      3. (iii)
        A student connects the blue coloured LED as shown in the figure. The LED did not glow when switch S is closed. Explain why? (Figure: a 1.5 V cell, the switch S, a resistor R and the LED in one loop. The cell's positive (long) plate faces the switch, so current goes round through S and R and reaches the LED at its bar (n side); the LED's arrow points against this current.)
      4. (iii) OR
        OR: Draw V-I characteristic of a p-n junction diode in (i) forward bias and (ii) reverse bias

      Tests: Light emitting diodes (no longer in the CBSE syllabus since 2023-24) and the V-I characteristic of a p-n junction diode (still in Chapter 14).

      Show solution

      (i) Why are LEDs made of compound semiconductor and not of elemental semiconductors?

      1. The photon energy is about the band gap. Silicon (1.1 eV) and germanium (0.7 eV) have band gaps that give photons in the infrared, not visible light (and, being indirect-gap materials, they release most of the recombination energy as heat).
      2. Compound semiconductors such as gallium arsenide-phosphide have band gaps of 1.8 to 3 eV, which can be set by their composition, so they emit visible light of the chosen colour efficiently.

        Why: The scheme's wording ('elemental conductor', 'detect the light') is garbled; the reason is the band gap.

      AnswerElemental Si/Ge band gaps give infrared; compound semiconductors have (adjustable) visible-range band gaps

      (ii) What should be the order of bandgap of an LED, if it is required to emit light in the visible range?

      1. Visible light runs from about 700 nm to 400 nm; E=hcλ=1240 eV nmλE = \dfrac{hc}{\lambda} = \dfrac{1240\ \text{eV nm}}{\lambda} gives about 1.8 eV to 3 eV. The band gap must be in this range.
      AnswerAbout 1.8 eV to 3 eV

      (iii) A student connects the blue coloured LED as shown in the figure. The LED did not glow when switch S is closed. Explain why? (Figure: a 1.5 V cell, the switch S, a resistor R and the LED in one loop. The cell's positive (long) plate faces the switch, so current goes round through S and R and reaches the LED at its bar (n side); the LED's arrow points against this current.)

      1. Following the current from the positive terminal, through S and R, it arrives at the LED's n side (cathode). The n side is at the higher potential, so the LED is reverse biased: no current flows, no electrons and holes recombine, and no light is emitted.
      2. Even if it were turned round (forward biased), 1.5 V would not light a blue LED: blue photons (about 450 nm) carry about 2.7 eV, so a blue LED needs roughly 2.5 to 3 V across it.

        Why: The marking scheme gives only the reverse bias; the voltage point is an extra check.

      AnswerThe LED is reverse biased (and 1.5 V is too little for a blue LED anyway)

      (iii) OR OR: Draw V-I characteristic of a p-n junction diode in (i) forward bias and (ii) reverse bias

      1. (i) Forward bias (first quadrant, V in volts, I in mA): the current stays almost zero up to the threshold (knee) voltage, about 0.7 V for silicon (0.2 V for germanium), and then rises steeply (exponentially) with voltage.
      2. (ii) Reverse bias (third quadrant, V in volts, I in μA): a very small, nearly constant reverse saturation current of a few μA, until at the breakdown voltage the reverse current rises suddenly.
      AnswerForward: negligible current until the knee, then a steep rise (mA); reverse: tiny constant current (μA) until breakdown
      Ask about this question

      Questions are quoted from the CBSE Class 12 Physics Sample Question Paper 2022-23 (subject code 042); figures are described in words. Every final answer is checked against the official CBSE marking scheme. Where a question offers a choice, both options are solved.

      Question papers are referenced for educational and review purposes only, under fair dealing. All copyrights in the questions belong to CBSE. Solutions and explanations provided here are original works by Your Abhyaasika, generated with AI, and may contain mistakes. Your Abhyaasika is not affiliated with CBSE or NCERT.