AI-generated solutions. The solutions and explanations on this page are written by AI. We check the final answers with automated tests, but AI can still make mistakes, especially in explanations and in figures described in words. If something looks wrong, ask in the doubt chat on that question or check with your teacher.

ICSE Class 10 Physics Specimen Paper 2025 with Solutions

Step-by-step solutions to every question of the ICSE 2025 Specimen Question Paper in Physics (Science Paper 1, subject code 521) for Class 10: the fifteen multiple-choice items and short answers of Section A, and all six questions of Section B, of which the exam asks for any four. Each answer is written the way the ICSE marking scheme awards marks (formula, substitution, result with units), and every answer is checked against the official CISCE draft marking scheme for the specimen; where the scheme's wording slips, the page follows the physics and says so.

ICSE 2025 Physics Specimen Question Paper (521): 23 questions, 80 marks, 2 hours. Open any question to see the steps one at a time or ask a doubt about a step. Also solved: Physics Specimen Paper 2026.

Section A: 40 marks: attempt all questions from this section

Q1 (i)

Question 1 (i) (1 mark)

Force and moments
A moment of couple has a tendency to rotate the body in an anticlockwise direction. Then the moment of couple is taken as:
  1. (A)positive
  2. (B)negative
  3. (C)maximum
  4. (D)zero

Tests: Sign convention for the moment of a force or couple.

Show solution
  1. Sign convention for moments: an anticlockwise moment is taken as positive, a clockwise moment as negative.
Answer(a) positive
Ask about this question
Q1 (ii)

Question 1 (ii) (1 mark)

Work, energy and power
The kinetic energy of a given body depends on the:
  1. (A)position
  2. (B)centre of gravity of the body.
  3. (C)momentum
  4. (D)displacement

Tests: Relation between kinetic energy and momentum.

Show solution
  1. K=12mv2=p22mK = \dfrac{1}{2}mv^2 = \dfrac{p^2}{2m}, where p=mvp = mv is the momentum.
  2. For a given body (fixed m) the kinetic energy depends only on its momentum. Position decides potential energy, not kinetic energy.
Answer(c) momentum
Ask about this question
Q1 (iii)

Question 1 (iii) (1 mark)

Work, energy and power
For burning of coal in a thermoelectric station, the energy conversion taking place is:
  1. (A)chemical to heat to mechanical
  2. (B)chemical to heat to mechanical to electrical
  3. (C)chemical to heat to light
  4. (D)heat to chemical to mechanical

Tests: Energy conversions in a thermal power station.

Show solution
  1. Burning coal releases its chemical energy as heat, which boils water into steam.
  2. The steam turns the turbine (mechanical energy), and the turbine drives the generator, which gives electrical energy.
Answer(b) chemical to heat to mechanical to electrical
Ask about this question
Q1 (iv)

Question 1 (iv) (1 mark)

Machines
The adjacent diagram shows the movable block of a block and tackle system with effort in a convenient direction. From the diagram we can conclude that the number of pulleys used in the fixed block are ________. (Photo: the movable block has a single pulley with the load hook below it; three rope strands rise from it: two pass round its pulley and the middle one ends in a loop tied to the top of the block.)
  1. (A)1
  2. (B)3
  3. (C)2
  4. (D)4

Tests: Velocity ratio of a block and tackle from the number of supporting strands.

Show solution
  1. Three strands of the string support the movable block, so V.R. = 3.
  2. With the effort in the convenient (downward) direction, V.R. = total number of pulleys in both blocks = 3.
  3. The movable block has 1 pulley, so the fixed block has 3 − 1 = 2 pulleys.

    Why: An odd V.R. means the string is tied to the movable block, which then has one pulley fewer than the fixed block.

Answer(c) 2
Ask about this question
Q1 (v)

Question 1 (v) (1 mark)

Refraction through a prism
White light is dispersed by a prism. Inside the prism, compared to the blue light, the red light
  1. (A)slows down less and refracts more
  2. (B)slows down more and refracts less
  3. (C)slows down more and refracts more
  4. (D)slows down less and refracts less

Tests: Dispersion: refractive index and speed depend on colour.

Show solution
  1. Glass has a smaller refractive index for red than for blue: μred<μblue\mu_{red} < \mu_{blue}.
  2. Speed in glass v=c/μv = c/\mu, so red travels faster (slows down less), and with a smaller μ\mu it bends (deviates) less.
Answer(d) slows down less and refracts less
Ask about this question
Q1 (vi)

Question 1 (vi) (1 mark)

Total internal reflection
An endoscope uses optic fiber to transmit high resolution images of internal organs without loss of information. The principle of light that is used by the optic fiber is based on:
  1. (A)refraction
  2. (B)reflection
  3. (C)scattering
  4. (D)total internal reflection.

Tests: Application of total internal reflection: optical fibres.

Show solution
  1. Light enters the glass fibre and strikes its wall (glass to a rarer cladding) at an angle greater than the critical angle.
  2. It is totally reflected again and again along the fibre with almost no loss: total internal reflection.
Answer(d) total internal reflection
Ask about this question
Q1 (vii)

Question 1 (vii) (1 mark)

Lenses
A convex lens has focal length 12 cm with an object at a distance of 20 cm in front of the lens. He obtains a blurred image on the screen placed at a distance of 23 cm in front of the lens. In order to obtain the clear image, he has to move the screen
  1. (A)towards the lens.
  2. (B)away from the lens.
  3. (C)to a position very far away from the lens.
  4. (D)either towards or away from the lens.

Tests: Locate a real image with the lens formula.

Show solution
  1. Lens formula 1v−1u=1f\dfrac{1}{v} - \dfrac{1}{u} = \dfrac{1}{f} with u=−20u = -20 cm, f=+12f = +12 cm.
  2. 1v=112−120=5−360=130\dfrac{1}{v} = \dfrac{1}{12} - \dfrac{1}{20} = \dfrac{5 - 3}{60} = \dfrac{1}{30}, so v=30v = 30 cm.
  3. The sharp image is 30 cm from the lens; the screen is at 23 cm, so it must move 7 cm away from the lens.
Answer(b) away from the lens
Ask about this question
Q1 (viii)

Question 1 (viii) (1 mark)

Electromagnetic spectrum
Assertion (A): Infrared radiations travel long distance through a dense fog and mist. Reason (R): Infrared radiations undergo minimal scattering in earth's atmosphere.
  1. (A)both A and R are true and R is the correct explanation of A.
  2. (B)both A and R are True and R is not the correct explanation of A.
  3. (C)assertion is false but reason is true.
  4. (D)assertion is true but reason is false.

Tests: Scattering depends on wavelength; why infrared penetrates fog.

Show solution
  1. Scattering by small particles is much weaker for long wavelengths (intensity ∝1/λ4\propto 1/\lambda^4). Infrared has a longer wavelength than visible light, so it is scattered very little: (R) is true.
  2. Because it is hardly scattered by fog droplets and mist, infrared passes through them over long distances (used in fog photography): (A) is true, and (R) is its explanation.
Answer(a) both A and R are true and R is the correct explanation of A
Ask about this question
Q1 (ix)

Question 1 (ix) (1 mark)

Sound
Two sound waves X and Y have the same amplitude and the same wave pattern but their frequencies are 60 Hz and 120 Hz respectively, then
  1. (A)X will be shriller and Y will be grave
  2. (B)X will be grave and Y will be shriller
  3. (C)X will differ in quality than Y
  4. (D)X is louder than Y.

Tests: Characteristics of sound: pitch, loudness and quality.

Show solution
  1. Pitch depends on frequency: the higher the frequency, the shriller the sound.
  2. Y (120 Hz) is shriller; X (60 Hz) is grave. Same amplitude means same loudness; same wave pattern means same quality.
Answer(b) X will be grave and Y will be shriller
Ask about this question
Q1 (x)

Question 1 (x) (1 mark)

Current electricity
The graph of voltage vs current for four different materials is shown below. (Graph: V on the vertical axis, I on the horizontal axis; four straight lines through the origin, P the steepest, then Q, then R, and S the least steep.) Which of these four materials would be used for making filament of a bulb?
  1. (A)Q
  2. (B)S
  3. (C)P
  4. (D)R

Tests: Reading resistance from the slope of a V-I graph.

Show solution
  1. For a V-I graph the slope is VI=R\dfrac{V}{I} = R, so the steepest line has the highest resistance.
  2. A filament must have a high resistance (high resistivity) so that it heats up and glows; P has the steepest line.
Answer(c) P
Ask about this question
Q1 (xi)

Question 1 (xi) (1 mark)

Household circuits
According to the old convention, the colour of the earth wire is:
  1. (A)black
  2. (B)green
  3. (C)yellow
  4. (D)red

Tests: Colour coding of household wiring.

Show solution
  1. Old convention: live red, neutral black, earth green. (New convention: live brown, neutral light blue, earth green or green with yellow stripes.)
Answer(b) green
Ask about this question
Q1 (xii)

Question 1 (xii) (1 mark)

Electromagnetism
Current is flowing through a coil as shown in the figure. Which one of the given figures will correctly depict the magnetic polarity and the direction of the lines of force along the axis of the coil? (Figure: a circular coil with a horizontal axis, seen slightly from one side; the current flows downward in its front half and upward in its back half. In each option the field lines are drawn along the axis on the left of the coil and a pole letter is written on the coil's face seen from the left.)
  1. (A)lines of force pointing away from the coil (to the left); face marked S
  2. (B)lines of force pointing into the coil (to the right); face marked N
  3. (C)lines of force pointing into the coil (to the right); face marked S
  4. (D)lines of force pointing away from the coil (to the left); face marked N

Tests: Clock rule and the direction of the field along the axis of a current loop.

Show solution
  1. Seen from the left, the front half of the coil is on the viewer's right with the current going down, and the back half on the left with the current going up: the current is clockwise.
  2. Clock rule: a face where the current is clockwise is a south pole, so the left face is S.
  3. Lines of force enter a south pole: along the axis they point into the coil from the left (and leave from the N face on the right). Only (c) shows S with the lines going in.
Answer(c) lines into the coil, face S
Ask about this question
Q1 (xiii)

Question 1 (xiii) (1 mark)

Calorimetry
Heat capacity of a body is the:
  1. (A)energy needed to melt a body without change in its temperature.
  2. (B)energy needed to raise the temperature of a body by 1°C
  3. (C)increase in volume of the body when its temperature increases by 1°C
  4. (D)total amount of internal energy that is constant.

Tests: Definition of heat capacity.

Show solution
  1. Heat capacity C′=QΔTC' = \dfrac{Q}{\Delta T}: the heat needed to raise the temperature of the whole body by 1 °C (or 1 K). Unit J K⁻¹.
Answer(b) energy needed to raise the temperature of a body by 1°C
Ask about this question
Q1 (xiv)

Question 1 (xiv) (1 mark)

Calorimetry
The amount of heat energy required to melt a given mass of a substance at its melting point without any rise in its temperature is called as the:
  1. (A)specific heat capacity
  2. (B)specific latent heat of fusion
  3. (C)latent heat of fusion
  4. (D)specific latent heat of freezing

Tests: Latent heat versus specific latent heat.

Show solution
  1. For a given mass (any mass) the heat to melt it at constant temperature is its latent heat of fusion, L = mℓ.
  2. Specific latent heat of fusion is the same quantity per unit mass (1 kg); the question says a given mass, so (c).
Answer(c) latent heat of fusion
Ask about this question
Q1 (xv)

Question 1 (xv) (1 mark)

Radioactivity
A nucleus of an atom consists of 146 neutrons and 95 protons. It decays after emitting an alpha particle. How many protons and neutrons are left in the nucleus after an alpha emission?
  1. (A)protons = 93 , neutrons = 142
  2. (B)protons = 95 , neutrons = 144
  3. (C)protons = 93 , neutrons = 144
  4. (D)protons = 95 , neutrons = 142

Tests: Change in proton and neutron numbers in alpha decay.

Show solution
  1. An alpha particle is a helium nucleus 24He^4_2\text{He}: 2 protons and 2 neutrons.
  2. Protons: 95−2=9395 - 2 = 93. Neutrons: 146−2=144146 - 2 = 144.
Answer(c) protons = 93, neutrons = 144
Ask about this question
Q2

Question 2 (10 marks)

Short answers: machines, energy, resistance, sound
(i) Complete the following by choosing the correct answers from the bracket. (ii) Graph of potential energy against height. (iii) Echo depth sounding.
  1. (i)(a)
    A ________ [class I / class II / Class III] lever will always have M.A. > 1.
  2. (i)(b)
    In a block and tackle system, increase in the weight of the movable block ________ [decreases, does not affect, increases] the efficiency of the pulley system.
  3. (i)(c)
    If the mass as well as the velocity of a body is doubled then the kinetic energy of the body ________ [is doubled / becomes eight times / becomes four times] the initial kinetic energy.
  4. (i)(d)
    Unit of power used in mechanical engineering is ________ [watt / horse power / erg per second].
  5. (i)(e)
    Two copper wires can have the different ________ [resistivity / resistance] but will have same ________ [resistance / resistivity].
  6. (ii)
    Draw a graph of potential energy vs height for a body thrown vertically upwards. [Assume no friction is present.]
  7. (iii)(a)
    Name the waves used for echo depth sounding.
  8. (iii)(b)
    Give one reason for their use in the above purpose.

Tests: Recall key facts: levers, pulley efficiency, kinetic energy, units, resistance versus resistivity, potential energy, SONAR.

Show solution

(i)(a) A ________ [class I / class II / Class III] lever will always have M.A. > 1.

  1. In a class II lever the load is between the fulcrum and the effort, so the effort arm is always longer than the load arm.
  2. M.A. =effort armload arm>1= \dfrac{\text{effort arm}}{\text{load arm}} > 1 always. (Class III always has M.A. < 1; class I can have any value.)
AnswerClass II

(i)(b) In a block and tackle system, increase in the weight of the movable block ________ [decreases, does not affect, increases] the efficiency of the pulley system.

  1. Part of the effort's work goes into lifting the movable block itself, which is wasted work.
  2. A heavier movable block wastes more work, so the useful output for the same input falls: efficiency decreases.
Answerdecreases

(i)(c) If the mass as well as the velocity of a body is doubled then the kinetic energy of the body ________ [is doubled / becomes eight times / becomes four times] the initial kinetic energy.

  1. K=12mv2K = \dfrac{1}{2}mv^2. New K′=12(2m)(2v)2=8×12mv2=8KK' = \dfrac{1}{2}(2m)(2v)^2 = 8 \times \dfrac{1}{2}mv^2 = 8K.
Answerbecomes eight times

(i)(d) Unit of power used in mechanical engineering is ________ [watt / horse power / erg per second].

  1. Engines and motors are rated in horse power (1 H.P. = 746 W); the watt is the SI unit, the erg per second the CGS unit.
Answerhorse power

(i)(e) Two copper wires can have the different ________ [resistivity / resistance] but will have same ________ [resistance / resistivity].

  1. Resistance R=ρlAR = \rho\dfrac{l}{A} depends on the length and thickness of the wire, so two copper wires can differ in resistance.
  2. Resistivity depends only on the material (and temperature), so both copper wires have the same resistivity.
Answerresistance; resistivity

(ii) Draw a graph of potential energy vs height for a body thrown vertically upwards. [Assume no friction is present.]

  1. Label the axes: potential energy U (J) on the vertical axis, height h (m) on the horizontal axis, origin (0, 0) at the point of projection.
  2. U=mghU = mgh with mgmg constant, so U∝hU \propto h: draw a straight line through the origin rising to the right.
AnswerA straight line through the origin: U (J) increases in direct proportion to h (m).

(iii)(a) Name the waves used for echo depth sounding.

  1. SONAR uses sound of frequency above 20 kHz: ultrasonic waves.
AnswerUltrasonic waves

(iii)(b) Give one reason for their use in the above purpose.

  1. Ultrasonic waves have a very short wavelength, so they can be sent as a narrow beam that travels long distances without spreading (deviating) much, and they are not easily absorbed by water.
AnswerThey can be confined to a narrow beam that travels long distances without deviation and is not easily absorbed.
Ask about this question
Q3

Question 3 (15 marks)

Short answers: lenses, earthing, transformer, heat, generator, radioactivity
Question 3 has seven short parts, (i) to (vii).
  1. (i)(a)
    A lens with two different refractive indices is shown: a biconvex lens whose upper half (above the principal axis) has refractive index μ1 and lower half μ2. If the rays are coming from a distant object, then how many images will be seen?
  2. (i)(b)
    A glass lens always forms a virtual, erect and diminished image of an object kept in front of it. Identify the lens.
  3. (ii)
    If live wire makes an accidental contact with the metal case, which circuit (A or B) in the diagram, illustrating an electric iron, is considered safe for the user (assuming the fuse is present in the live wire in both circuits)? Justify your answer. (Diagram: in both, a 220 V supply L-N feeds the iron's coil inside a metal case touched by a person. In A the metal case is connected to earth; in B the neutral wire is earthed and the metal case is not.)
  4. (iii)(a)
    A transformer is used to change a high alternating e.m.f. to a low alternating e.m.f. of the same frequency. Identify the type of transformer used for the above purpose.
  5. (iii)(b)
    State whether the turns ratio of the above transformer is = 1 or > 1 or < 1.
  6. (iv)
    A solid of mass 60 g at 100 °C is placed in 150 g of water at 20 °C. The final steady temperature is 25 °C. Calculate the heat capacity of solid. [sp. heat capacity of water = 4.2 J g−1K−1\text{J g}^{-1}\text{K}^{-1}]
  7. (v)(a)
    Name the principle of AC generator.
  8. (v)(b)
    State its one use.
  9. (vi)(a)
    Name the radiations that are emitted during the decay of a nucleus, which has highest penetrating power.
  10. (vi)(b)
    Does the emission of the above-mentioned radiation result in a change in the mass number?
  11. (vii)(a)
    Fig. A plots the number of neutrons (y-axis) against the number of protons (x-axis) for elements A, B, C, D and E: A (88, 144), B (90, 144), C (92, 146), D (93, 146), E (93, 145). When the element C undergoes radioactive decay, it releases radioactive rays. When these rays are directed into the plane of the paper in a magnetic field (Fig. B: the N pole on the left, the S pole on the right, so the field points left to right), they are deflected upwards. Name the radioactive radiations emitted by the element C.
  12. (vii)(b)
    Identify the daughter element from the graph.
  13. (vii)(c)
    Name the law used to identify the radioactive radiations emitted by the element.

Tests: Lenses, earthing, transformers, the principle of mixtures, AC generators and identifying radiation from its deflection and an N-Z plot.

Show solution

(i)(a) A lens with two different refractive indices is shown: a biconvex lens whose upper half (above the principal axis) has refractive index μ1 and lower half μ2. If the rays are coming from a distant object, then how many images will be seen?

  1. The focal length of a lens depends on the refractive index of its material, so the two halves have different focal lengths.
  2. Each half forms its own image of the distant object at its own focus: two images.
Answer2 images

(i)(b) A glass lens always forms a virtual, erect and diminished image of an object kept in front of it. Identify the lens.

  1. A concave lens forms a virtual, erect, diminished image for every position of the object; a convex lens gives a virtual image only when the object is inside F, and then it is magnified.
AnswerConcave lens

(ii) If live wire makes an accidental contact with the metal case, which circuit (A or B) in the diagram, illustrating an electric iron, is considered safe for the user (assuming the fuse is present in the live wire in both circuits)? Justify your answer. (Diagram: in both, a 220 V supply L-N feeds the iron's coil inside a metal case touched by a person. In A the metal case is connected to earth; in B the neutral wire is earthed and the metal case is not.)

  1. In A the metal case is earthed: if the live wire touches the case, a large current flows straight to earth through the low-resistance earth wire, the fuse blows, and the case stays at earth potential, so the person gets no shock.
  2. In B the case is not earthed: it rises to 220 V and the circuit is completed to earth through the person's body, giving a shock.
AnswerCircuit A, because its metal case is earthed.

(iii)(a) A transformer is used to change a high alternating e.m.f. to a low alternating e.m.f. of the same frequency. Identify the type of transformer used for the above purpose.

  1. A transformer that lowers the voltage is a step-down transformer.
AnswerStep-down transformer

(iii)(b) State whether the turns ratio of the above transformer is = 1 or > 1 or < 1.

  1. Turns ratio n=NsNp=VsVpn = \dfrac{N_s}{N_p} = \dfrac{V_s}{V_p}.
  2. Step down: Vs<VpV_s < V_p, so Ns<NpN_s < N_p and n<1n < 1.
AnswerLess than 1

(iv) A solid of mass 60 g at 100 °C is placed in 150 g of water at 20 °C. The final steady temperature is 25 °C. Calculate the heat capacity of solid. [sp. heat capacity of water = 4.2 J g−1K−1\text{J g}^{-1}\text{K}^{-1}]

  1. Principle of mixtures: heat lost by the solid = heat gained by the water.
  2. Heat gained by water =mcΔT=150×4.2×(25−20)=3150= mc\Delta T = 150 \times 4.2 \times (25 - 20) = 3150 J.
  3. Heat lost by solid =C′×(100−25)=75 C′= C' \times (100 - 25) = 75\,C'. So 75 C′=315075\,C' = 3150, C′=42 J K−1C' = 42\ \text{J K}^{-1}.
AnswerHeat capacity of the solid =42 J K−1= 42\ \text{J K}^{-1}

(v)(a) Name the principle of AC generator.

  1. When the magnetic flux linked with a coil changes (the coil rotates in a magnetic field), an e.m.f. is induced in it: electromagnetic induction (Faraday's laws).
AnswerElectromagnetic induction (Faraday's law)

(v)(b) State its one use.

  1. AC generators produce the electricity supplied by power stations; portable generators also serve as back-up supply (for lifts, hospitals) during a power failure.
AnswerTo generate electricity in power stations (or as a back-up supply during power failure).

(vi)(a) Name the radiations that are emitted during the decay of a nucleus, which has highest penetrating power.

  1. Of alpha, beta and gamma radiation, gamma rays (uncharged electromagnetic waves) penetrate most; they pass through several cm of lead.
AnswerGamma (γ) radiation

(vi)(b) Does the emission of the above-mentioned radiation result in a change in the mass number?

  1. A gamma ray is a photon with no mass and no charge; it only carries away the excess energy of the nucleus, so both the mass number and the atomic number stay the same.
AnswerNo

(vii)(a) Fig. A plots the number of neutrons (y-axis) against the number of protons (x-axis) for elements A, B, C, D and E: A (88, 144), B (90, 144), C (92, 146), D (93, 146), E (93, 145). When the element C undergoes radioactive decay, it releases radioactive rays. When these rays are directed into the plane of the paper in a magnetic field (Fig. B: the N pole on the left, the S pole on the right, so the field points left to right), they are deflected upwards. Name the radioactive radiations emitted by the element C.

  1. Fleming's left-hand rule for a positive charge: field to the right (forefinger), motion into the paper (middle finger), so the force (thumb) is downward.
  2. The rays are deflected upward, opposite to that, so they carry negative charge: beta particles (electrons).
AnswerBeta (β) radiation

(vii)(b) Identify the daughter element from the graph.

  1. Beta decay turns a neutron into a proton: protons + 1, neutrons − 1, mass number unchanged.
  2. C (92 protons, 146 neutrons) becomes (93, 145), which is E: 92238C→93238E+−10β^{238}_{92}\text{C} \to {}^{238}_{93}\text{E} + {}^{0}_{-1}\beta.
AnswerE

(vii)(c) Name the law used to identify the radioactive radiations emitted by the element.

  1. The direction of the force on a moving charge (a current) in a magnetic field is given by Fleming's left-hand rule.
AnswerFleming's left-hand rule
Ask about this question

Section B: 40 marks: attempt any four questions from this section

Q4

Question 4 (10 marks)

Refraction, total internal reflection and the spectrum
Question 4: (i) a fish's image at the water surface and a lens in two liquids, (ii) refractive index and temperature, (iii) a mixed beam through a convex lens.
  1. (i)(a)
    A photograph shows a fish in a tank and its inverted image seen in the surface of the water (from below). Name the phenomenon responsible for the formation of this image.
  2. (i)(b)(1)
    A double convex lens of refractive index μ1\mu_1 is placed in two liquids: Figure a, liquid 1 of refractive index μ3\mu_3; Figure b, liquid 2 of refractive index μ2\mu_2, with μ2>μ1\mu_2 > \mu_1 and μ1>μ3\mu_1 > \mu_3. How would a parallel incident beam of light refract when it comes out of the lens in Fig. a?
  3. (i)(b)(2)
    How would the beam refract when it comes out of the lens in Fig. b?
  4. (ii)(a)
    The refractive index of water is 1.33 at a certain temperature. When the temperature of water is increased by 40 °C, the refractive index changes to x. State whether x < 1.33 or x > 1.33.
  5. (ii)(b)
    State two differences between normal reflection and total internal reflection.
  6. (iii)(a)
    A mixture of red + blue + green light is passed through a convex lens as a ray parallel to the principal axis. State whether the ray passes through a single point or through different points on the principal axis after refraction.
  7. (iii)(b)
    Name the invisible radiations which are studied using the quartz prism.
  8. (iii)(c)
    State one use of these radiations.
  9. (iii)(d)
    Name one radiation having the wavelength longer than the wavelength of these radiations.

Tests: Total internal reflection, a lens in a denser or rarer liquid, dispersion by a lens and the ultraviolet region.

Show solution

(i)(a) A photograph shows a fish in a tank and its inverted image seen in the surface of the water (from below). Name the phenomenon responsible for the formation of this image.

  1. Light from the fish travels up through water (denser) towards the water-air surface (rarer).
  2. Where it meets the surface at more than the critical angle (about 49° for water) it is totally reflected back into the water, so the surface acts as a mirror: total internal reflection.
AnswerTotal internal reflection

(i)(b)(1) A double convex lens of refractive index μ1\mu_1 is placed in two liquids: Figure a, liquid 1 of refractive index μ3\mu_3; Figure b, liquid 2 of refractive index μ2\mu_2, with μ2>μ1\mu_2 > \mu_1 and μ1>μ3\mu_1 > \mu_3. How would a parallel incident beam of light refract when it comes out of the lens in Fig. a?

  1. In liquid 1 the lens is optically denser than its surroundings (μ1>μ3\mu_1 > \mu_3), so it behaves like a convex lens in air.
  2. The parallel beam converges after leaving the lens.
AnswerIt converges.

(i)(b)(2) How would the beam refract when it comes out of the lens in Fig. b?

  1. In liquid 2 the lens is optically rarer than its surroundings (μ1<μ2\mu_1 < \mu_2), so light bends the other way at each surface.
  2. The double convex lens acts as a diverging lens: the beam diverges.
AnswerIt diverges.

(ii)(a) The refractive index of water is 1.33 at a certain temperature. When the temperature of water is increased by 40 °C, the refractive index changes to x. State whether x < 1.33 or x > 1.33.

  1. On heating, water expands and its optical density falls, so light travels faster in it and its refractive index decreases.
Answerx < 1.33

(ii)(b) State two differences between normal reflection and total internal reflection.

  1. 1. Normal reflection can take place in any medium, denser or rarer; total internal reflection only when light goes from a denser medium towards a rarer one.
  2. 2. Normal reflection takes place at any angle of incidence; total internal reflection only when the angle of incidence exceeds the critical angle.
  3. (Also: in normal reflection from a mirror some light is absorbed; total internal reflection reflects all the light.)
AnswerReflection: any medium, any angle of incidence. TIR: only from a denser medium, only for angles of incidence greater than the critical angle.

(iii)(a) A mixture of red + blue + green light is passed through a convex lens as a ray parallel to the principal axis. State whether the ray passes through a single point or through different points on the principal axis after refraction.

  1. The refractive index of glass is different for each colour (largest for blue, smallest for red), so each colour is deviated by a different amount.
  2. Blue meets the axis closest to the lens, then green, then red: the colours cross the axis at different points.
AnswerThrough different points (blue nearest the lens, red farthest).

(iii)(b) Name the invisible radiations which are studied using the quartz prism.

  1. Ordinary glass absorbs ultraviolet radiation but quartz transmits it, so ultraviolet spectra are studied with a quartz prism.
AnswerUltraviolet radiations

(iii)(c) State one use of these radiations.

  1. Ultraviolet radiation kills germs, so it is used to sterilise water, surgical instruments and food; it is also used to detect fake notes and gems and helps the skin make vitamin D.
AnswerSterilisation (killing germs in water and on instruments).

(iii)(d) Name one radiation having the wavelength longer than the wavelength of these radiations.

  1. In order of increasing wavelength: ultraviolet < visible < infrared < microwaves < radio waves.
AnswerInfrared (or visible light, microwaves, radio waves).
Ask about this question
Q5

Question 5 (10 marks)

Lenses, dispersion and total internal reflection
Question 5: (i) image by a convex lens, (ii) rainbow and prism, (iii) rays from a luminous point inside a glass block.
  1. (i)(a)
    An object is placed at a distance 24 cm in front of a convex lens of focal length 8 cm. What is the nature of the image so formed?
  2. (i)(b)
    Calculate the distance of the image from the lens.
  3. (ii)(a)
    When sunlight passes through water droplets in the atmosphere it gets dispersed into its constituent colours forming a rainbow. A similar phenomenon is observed when white light passes through a prism. Which colour will show the maximum angle of deviation and which colour will show the minimum angle of deviation?
  4. (ii)(b)
    If instead of sunlight, a green-coloured ray is passed through a glass prism, what will be the colour of the emergent ray?
  5. (iii)(b)
    O is a luminescent particle trapped inside a glass block. A student traces the path of rays coming out of it and reflecting over a plane mirror. (Figure: from O, ray R goes up-left to the block's left face; there it refracts out into air as ray Q, which makes angle e with the face, while ray U is reflected back into the block. Q strikes a plane mirror above, making angle b with the mirror's normal, and leaves as ray P, which makes angle a with the normal. A second ray S from O meets the left face lower down at angle c with the normal and emerges as ray T, grazing along the face.) Complete the table using the labels from the figure (row a., an angle of reflection on the mirror, is a). b. A partially reflected ray in the glass slab.
  6. (iii)(c)
    c. A critical angle.
  7. (iii)(d)
    d. A refracted ray.
  8. (iii)(e)
    e. An angle of refraction of the ray R.

Tests: Lens formula and image nature; dispersion; identifying reflected, refracted rays and the critical angle.

Show solution

(i)(a) An object is placed at a distance 24 cm in front of a convex lens of focal length 8 cm. What is the nature of the image so formed?

  1. The object is beyond 2F (24 cm > 16 cm), so the image forms between F and 2F on the other side: real, inverted and diminished.
AnswerReal and inverted (and diminished)

(i)(b) Calculate the distance of the image from the lens.

  1. Lens formula 1v−1u=1f\dfrac{1}{v} - \dfrac{1}{u} = \dfrac{1}{f}, with u=−24u = -24 cm and f=+8f = +8 cm.
  2. 1v=18+1−24=3−124=112\dfrac{1}{v} = \dfrac{1}{8} + \dfrac{1}{-24} = \dfrac{3 - 1}{24} = \dfrac{1}{12}.
  3. v=+12v = +12 cm: the image is 12 cm from the lens, on the other side.
Answer12 cm from the lens (on the other side)

(ii)(a) When sunlight passes through water droplets in the atmosphere it gets dispersed into its constituent colours forming a rainbow. A similar phenomenon is observed when white light passes through a prism. Which colour will show the maximum angle of deviation and which colour will show the minimum angle of deviation?

  1. Glass has the largest refractive index for violet and the smallest for red, so violet is deviated most and red least.
AnswerMaximum: violet; minimum: red.

(ii)(b) If instead of sunlight, a green-coloured ray is passed through a glass prism, what will be the colour of the emergent ray?

  1. A prism does not create colours; it only separates the colours already present. Green is a single colour, so it is only deviated, not split.
AnswerGreen

(iii)(b) O is a luminescent particle trapped inside a glass block. A student traces the path of rays coming out of it and reflecting over a plane mirror. (Figure: from O, ray R goes up-left to the block's left face; there it refracts out into air as ray Q, which makes angle e with the face, while ray U is reflected back into the block. Q strikes a plane mirror above, making angle b with the mirror's normal, and leaves as ray P, which makes angle a with the normal. A second ray S from O meets the left face lower down at angle c with the normal and emerges as ray T, grazing along the face.) Complete the table using the labels from the figure (row a., an angle of reflection on the mirror, is a). b. A partially reflected ray in the glass slab.

  1. At the face, ray R is partly refracted out (Q) and partly reflected back into the glass: the reflected part is U.
AnswerU

(iii)(c) c. A critical angle.

  1. Ray S meets the face at angle c with the normal and emerges grazing the surface (angle of refraction 90°, ray T): so c is the critical angle.
Answerc

(iii)(d) d. A refracted ray.

  1. Ray R bends away from the normal as it leaves the glass and goes on in air as Q: Q is a refracted ray. (T, the grazing ray at the critical angle, is also a refracted ray.)
AnswerQ (or T)

(iii)(e) e. An angle of refraction of the ray R.

  1. The angle of refraction is measured between the refracted ray Q and the normal to the face.
  2. e is the angle between Q and the face itself, and the normal is at 90° to the face, so the angle of refraction is 90° − e.
Answer90° − e
Ask about this question
Q6

Question 6 (10 marks)

Moments, work and energy
Question 6: (i) a non-uniform rod balanced off-centre, (ii) sign of work done by gravity, (iii) energy of a simple pendulum.
  1. (i)(a)
    A metal rod AB of length 80 cm is balanced at 45 cm from the end A with 100 gf weights suspended from the two ends (A at 0 cm, centre C at 40 cm, fulcrum at 45 cm, B at 80 cm). If this rod is cut at the centre C, then compare the weight of AC to the weight of BC.
  2. (i)(b)
    Give a reason for your answer in (a).
  3. (ii)(a)
    State whether the work done by gravity is positive, negative, or zero: a person walks on a levelled road.
  4. (ii)(b)
    A person climbs a ladder.
  5. (ii)(c)
    A car in neutral gear is coming down the slope.
  6. (iii)(a)
    A simple pendulum of mass 200 g is displaced from the mean position A to the extreme position B. The potential energy at the position A is zero. At the position B the pendulum bob is raised by 5 m. (C is a position between A and B.) Take g = 10 m s⁻² and no loss of energy. What is the potential energy of the pendulum at the position B?
  7. (iii)(b)
    What is the total mechanical energy at point C?
  8. (iii)(c)
    What is the speed of the bob at the position A when released from B?

Tests: Principle of moments for a non-uniform rod; sign of work; conservation of mechanical energy in a pendulum.

Show solution

(i)(a) A metal rod AB of length 80 cm is balanced at 45 cm from the end A with 100 gf weights suspended from the two ends (A at 0 cm, centre C at 40 cm, fulcrum at 45 cm, B at 80 cm). If this rod is cut at the centre C, then compare the weight of AC to the weight of BC.

  1. Moments of the two 100 gf weights about the fulcrum: at A, 100 × 45 = 4500 gf cm anticlockwise; at B, 100 × 35 = 3500 gf cm clockwise.
  2. For balance the rod's own weight must supply 1000 gf cm clockwise, so its centre of gravity lies on the B side of the fulcrum, beyond 45 cm (beyond the centre C at 40 cm).
  3. More of the rod's mass is in CB than in AC.
AnswerWeight of AC < weight of BC

(i)(b) Give a reason for your answer in (a).

  1. The two end weights are equal, but the moment arm of B (35 cm) is shorter than that of A (45 cm), so they alone would tip the rod towards A.
  2. The rod balances only because the moment of its own weight acts on the B side: its centre of gravity lies beyond the 45 cm mark, past the midpoint C, so the rod is non-uniform with more weight between C and B.
AnswerThe rod's centre of gravity lies beyond 45 cm on the B side, so more of its weight is in CB.

(ii)(a) State whether the work done by gravity is positive, negative, or zero: a person walks on a levelled road.

  1. Gravity acts vertically down; the displacement is horizontal (90°): W = Fs cos 90° = 0.
AnswerZero (no work is done)

(ii)(b) A person climbs a ladder.

  1. The displacement is upward, opposite to gravity (180°): W = Fs cos 180° < 0.
AnswerNegative

(ii)(c) A car in neutral gear is coming down the slope.

  1. The car moves downhill: its displacement has a component along gravity (angle less than 90°), so gravity does positive work (it is what speeds the car up).
AnswerPositive

(iii)(a) A simple pendulum of mass 200 g is displaced from the mean position A to the extreme position B. The potential energy at the position A is zero. At the position B the pendulum bob is raised by 5 m. (C is a position between A and B.) Take g = 10 m s⁻² and no loss of energy. What is the potential energy of the pendulum at the position B?

  1. m = 200 g = 0.2 kg, h = 5 m.
  2. U=mgh=0.2×10×5=10U = mgh = 0.2 \times 10 \times 5 = 10 J.
Answer10 J

(iii)(b) What is the total mechanical energy at point C?

  1. With no loss of energy, the total mechanical energy (U + K) is the same at every point of the swing (conservation of energy).
  2. At B it is all potential energy, 10 J (K = 0 at the extreme), so at C, U + K = 10 J.
Answer10 J

(iii)(c) What is the speed of the bob at the position A when released from B?

  1. Conservation of energy: U at B = K at A, so 10=12×0.2×v210 = \dfrac{1}{2} \times 0.2 \times v^2.
  2. v2=100v^2 = 100, v=10 m s−1v = 10\ \text{m s}^{-1}.
Answer10 m/s
Ask about this question
Q7

Question 7 (10 marks)

Machines, echoes and resonance
Question 7: (i) block and tackle with velocity ratio 4, (ii) echo from a cliff, (iii) pushing a swing.
  1. (i)(a)
    A block and tackle system of pulleys has velocity ratio 4. Draw a labelled diagram of the system indicating clearly the direction of the load and effort.
  2. (i)(b)
    Calculate the potential energy of the load 100 kgf lifted by this pulley to a height 5 m. (g = 10 m s⁻²)
  3. (ii)(a)
    A person standing in front of a cliff fires a gun and hears its echo after 3 s. If the speed of sound in air is 336 m s⁻¹, calculate the distance of the person from the cliff.
  4. (ii)(b)
    After moving a certain distance from the cliff, he fires the gun again and this time the echo is heard 1.5 s later than the first. Calculate the distance that the person moved.
  5. (iii)(a)
    A mother pushes her daughter sitting on a swing. The swing goes through positions A, B, C, where A and C are the extreme positions (A on the mother's side) and B is the mean position. Which is the right position, A, B or C, for the mother to give a constant periodic push to the swing every time in the forward direction to increase the amplitude of the swing?
  6. (iii)(b)
    Name the phenomenon involved in this.
  7. (iii)(c)
    Explain with this example how this phenomenon helps to increase the amplitude of the swing.

Tests: Block and tackle, potential energy, echoes and resonance.

Show solution

(i)(a) A block and tackle system of pulleys has velocity ratio 4. Draw a labelled diagram of the system indicating clearly the direction of the load and effort.

  1. Upper block: two pulleys, fixed to a rigid support. Lower block: two pulleys, movable, with the load L hung from its hook.
  2. One continuous string: tied to the hook of the upper block, passing alternately round the lower and upper pulleys, so four segments of string support the lower block; the free end comes off the last upper pulley.
  3. Mark the tension T in each of the four segments (upward on the lower block), the load L acting vertically down, and the effort E applied downward at the free end.
  4. V.R. = number of string segments supporting the lower block = 4.
AnswerDiagram: 2 fixed + 2 movable pulleys, one string, 4 segments with tension T supporting the load L (down); effort E downward at the free end.

(i)(b) Calculate the potential energy of the load 100 kgf lifted by this pulley to a height 5 m. (g = 10 m s⁻²)

  1. A load of 100 kgf is the weight of a 100 kg mass.
  2. U=mgh=100×10×5=5000U = mgh = 100 \times 10 \times 5 = 5000 J.
Answer5000 J

(ii)(a) A person standing in front of a cliff fires a gun and hears its echo after 3 s. If the speed of sound in air is 336 m s⁻¹, calculate the distance of the person from the cliff.

  1. The sound goes to the cliff and back: 2d=vt2d = vt, so d=vt2d = \dfrac{vt}{2}.
  2. d=336×32=504d = \dfrac{336 \times 3}{2} = 504 m.
Answer504 m

(ii)(b) After moving a certain distance from the cliff, he fires the gun again and this time the echo is heard 1.5 s later than the first. Calculate the distance that the person moved.

  1. Moving away from the cliff, the echo now takes 3 + 1.5 = 4.5 s.
  2. New distance d′=336×4.52=756d' = \dfrac{336 \times 4.5}{2} = 756 m.
  3. Distance moved = 756 − 504 = 252 m (away from the cliff).

    Why: The extra 1.5 s is the time for the extra distance there and back: 336×1.52=252\dfrac{336 \times 1.5}{2} = 252 m, which is how the scheme works it.

Answer252 m

(iii)(a) A mother pushes her daughter sitting on a swing. The swing goes through positions A, B, C, where A and C are the extreme positions (A on the mother's side) and B is the mean position. Which is the right position, A, B or C, for the mother to give a constant periodic push to the swing every time in the forward direction to increase the amplitude of the swing?

  1. Push at the extreme position next to her, where the swing is momentarily at rest and about to move forward: each push then adds energy in step with the motion.
AnswerAt A

(iii)(b) Name the phenomenon involved in this.

  1. A periodic force applied at the natural frequency of the body gives large amplitude: resonance.
AnswerResonance

(iii)(c) Explain with this example how this phenomenon helps to increase the amplitude of the swing.

  1. The mother pushes once every oscillation, so the frequency of her push equals the natural frequency of the swing.
  2. Each push is in the direction of motion and in phase with it, so energy is added every cycle; the energy builds up and the amplitude increases.
AnswerThe pushes come at the swing's natural frequency and in phase with it, so energy is added every cycle and the amplitude grows (resonance).
Ask about this question
Q8

Question 8 (10 marks)

Current electricity and radioactivity
Question 8: (i) a mercury-filled tube as a resistor, (ii) alpha and beta decays, (iii) a series-parallel circuit with internal resistance.
  1. (i)(a)
    A circuit for studying Ohm's law: a battery, an ammeter and a glass tube filled with mercury (tube 1) in series, connected through two electrodes E1 and E2, with a voltmeter across the tube. The student repeats the experiment with tube 2, which the same amount of mercury fills; tube 2 is shorter and wider than tube 1. Neglecting internal resistance of the cell, use (> or < or =) to compare the resistance in both the cases.
  2. (i)(b)
    Compare the voltmeter readings in both the cases.
  3. (i)(c)
    Compare the specific resistance in both the cases.
  4. (ii)(a)
    A radioactive nucleus X emits an alpha particle followed by two beta particles to form nucleus Y. With respect to the element X, where would you position the element Y in the periodic table?
  5. (ii)(b)
    What is the general name of the elements X and Y?
  6. (ii)(c)
    If the atomic number of Y is 80 then what is the atomic number of X?
  7. (iii)(a)
    In the circuit, a 5 Ω and a 3 Ω resistor are in series, and a 2 Ω resistor is connected in parallel across the pair; this combination is connected through a key K to a cell of e.m.f. 4 V and internal resistance 0.4 Ω. Calculate the resistance of the circuit when the key K completes the circuit.
  8. (iii)(b)
    Calculate the current through 3 Ω resistance when the circuit is complete.

Tests: Resistance versus resistivity, alpha and beta decay arithmetic, and a circuit with internal resistance.

Show solution

(i)(a) A circuit for studying Ohm's law: a battery, an ammeter and a glass tube filled with mercury (tube 1) in series, connected through two electrodes E1 and E2, with a voltmeter across the tube. The student repeats the experiment with tube 2, which the same amount of mercury fills; tube 2 is shorter and wider than tube 1. Neglecting internal resistance of the cell, use (> or < or =) to compare the resistance in both the cases.

  1. R=ρlAR = \rho\dfrac{l}{A}. The same volume of mercury in tube 2 forms a shorter, thicker column: ll smaller, AA larger.
  2. Both changes lower the resistance.
AnswerRtube 2<Rtube 1R_{\text{tube 2}} < R_{\text{tube 1}}

(i)(b) Compare the voltmeter readings in both the cases.

  1. With no internal resistance (and an ideal ammeter), the whole battery voltage appears across the tube in both cases: the voltmeter reading is the same, V1 = V2 (only the current changes).
AnswerV1=V2V_1 = V_2

(i)(c) Compare the specific resistance in both the cases.

  1. Specific resistance (resistivity) depends only on the material and temperature; both tubes hold mercury, so it is the same: ρ1 = ρ2.
Answerρ1=ρ2\rho_1 = \rho_2

(ii)(a) A radioactive nucleus X emits an alpha particle followed by two beta particles to form nucleus Y. With respect to the element X, where would you position the element Y in the periodic table?

  1. Alpha emission: Z→Z−2Z \to Z - 2, A→A−4A \to A - 4. Each beta emission: Z→Z+1Z \to Z + 1, AA unchanged.
  2. Net: Z−2+2=ZZ - 2 + 2 = Z and A−4A - 4: ZAX→ZA−4Y^{A}_{Z}\text{X} \to {}^{A-4}_{Z}\text{Y}. The atomic number is unchanged, so Y occupies the same place as X.
AnswerAt the same place as X

(ii)(b) What is the general name of the elements X and Y?

  1. Same atomic number (same element), different mass numbers (A and A − 4): isotopes.
AnswerIsotopes

(ii)(c) If the atomic number of Y is 80 then what is the atomic number of X?

  1. The alpha and two beta emissions leave the atomic number unchanged: Z of X = Z of Y = 80.
Answer80

(iii)(a) In the circuit, a 5 Ω and a 3 Ω resistor are in series, and a 2 Ω resistor is connected in parallel across the pair; this combination is connected through a key K to a cell of e.m.f. 4 V and internal resistance 0.4 Ω. Calculate the resistance of the circuit when the key K completes the circuit.

  1. Series: 5 + 3 = 8 Ω.
  2. In parallel with 2 Ω: Rp=8×28+2=1.6 ΩR_p = \dfrac{8 \times 2}{8 + 2} = 1.6\ \Omega.
  3. Total with the internal resistance: R=1.6+0.4=2 ΩR = 1.6 + 0.4 = 2\ \Omega.
Answer2 Ω

(iii)(b) Calculate the current through 3 Ω resistance when the circuit is complete.

  1. Total current I=ER=42=2I = \dfrac{E}{R} = \dfrac{4}{2} = 2 A.
  2. The current divides inversely as the branch resistances: I3Ω=2×22+8=0.4I_{3\Omega} = \dfrac{2 \times 2}{2 + 8} = 0.4 A (the 3 Ω is in the 8 Ω branch).

    Why: Check: p.d. across the combination =2×1.6=3.2= 2 \times 1.6 = 3.2 V, and 3.2/8=0.43.2 / 8 = 0.4 A.

Answer0.4 A
Ask about this question
Q9

Question 9 (10 marks)

Calorimetry and electromagnetism
Question 9: (i) cooling water with ice, (ii) a cooling curve, (iii) the magnetic field of a current loop.
  1. (i)
    What mass of ice at 0 °C added to 2.1 kg water, will cool it down from 75 °C to 25 °C? Given specific heat capacity of water = 4.2 J g−1 ∘C−1\text{J g}^{-1}\,{}^\circ\text{C}^{-1}, specific latent heat of ice = 336 J g−1\text{J g}^{-1}.
  2. (ii)(a)
    A cooling curve (temperature in °C against time) for a substance: flat at 150 °C, then falling to 60 °C, flat at 60 °C, then falling to 10 °C. State the temperatures at which the substance condenses.
  3. (ii)(b)
    The temperature range in which the substance is in liquid state.
  4. (ii)(c)
    Why do we prefer ice to ice-cold water for cooling a drink?
  5. (iii)(a)
    A wire bent in the form of a loop passes through a cardboard on which iron filings are kept; its ends are joined through a rheostat to battery terminals A and B. When current flows, the filings form circles round the two points where the wire passes through the board; with the field directions marked, the field lines circle the left point anticlockwise and the right point clockwise (seen from above). The left end of the loop leads to A and the right end to B. State the polarities of the battery at A and B.
  6. (iii)(b)
    State the effect on the magnetic field if an iron rod is held along the axis of the coil.
  7. (iii)(c)(1)
    State one way to change the polarity of the coil.
  8. (iii)(c)(2)
    State one way to decrease the strength of the magnetic field around the coil.

Tests: Principle of mixtures with latent heat; reading a cooling curve; the field of a current loop.

Show solution

(i) What mass of ice at 0 °C added to 2.1 kg water, will cool it down from 75 °C to 25 °C? Given specific heat capacity of water = 4.2 J g−1 ∘C−1\text{J g}^{-1}\,{}^\circ\text{C}^{-1}, specific latent heat of ice = 336 J g−1\text{J g}^{-1}.

  1. Heat lost by the water = heat gained by the ice (to melt) + heat gained by the melted ice (0 °C to 25 °C). Work in grams: 2.1 kg = 2100 g.
  2. Heat lost by water =2100×4.2×(75−25)=441 000= 2100 \times 4.2 \times (75 - 25) = 441\,000 J.
  3. Heat gained by ice of mass mm: m×336+m×4.2×(25−0)=336m+105m=441mm \times 336 + m \times 4.2 \times (25 - 0) = 336m + 105m = 441m J.
  4. 441m=441 000⇒m=1000441m = 441\,000 \Rightarrow m = 1000 g.
Answer1000 g (1 kg) of ice

(ii)(a) A cooling curve (temperature in °C against time) for a substance: flat at 150 °C, then falling to 60 °C, flat at 60 °C, then falling to 10 °C. State the temperatures at which the substance condenses.

  1. On a cooling curve a flat part is a change of state: the temperature stays constant while latent heat is given out.
  2. The first plateau, at 150 °C, is the gas turning into liquid (condensation); the second, at 60 °C, is the liquid freezing.
Answer150 °C

(ii)(b) The temperature range in which the substance is in liquid state.

  1. The substance is liquid from the end of condensation at 150 °C until freezing begins at 60 °C (the falling part between the two plateaus).
Answer150 °C to 60 °C

(ii)(c) Why do we prefer ice to ice-cold water for cooling a drink?

  1. Ice at 0 °C must first melt, taking in its specific latent heat of 336 J for every gram, before it can warm up like ice-cold water.
  2. So each gram of ice absorbs 336 J more heat from the drink than a gram of water at 0 °C, cooling it much more.
AnswerEach gram of ice absorbs 336 J more heat (its latent heat of fusion) than ice-cold water.

(iii)(a) A wire bent in the form of a loop passes through a cardboard on which iron filings are kept; its ends are joined through a rheostat to battery terminals A and B. When current flows, the filings form circles round the two points where the wire passes through the board; with the field directions marked, the field lines circle the left point anticlockwise and the right point clockwise (seen from above). The left end of the loop leads to A and the right end to B. State the polarities of the battery at A and B.

  1. Right-hand thumb rule: anticlockwise field lines (seen from above) mean the current comes up through the board; clockwise lines mean it goes down.
  2. So the current flows up the left side of the loop, over the top and down the right side: it enters the loop from A and returns to B.
  3. Conventional current leaves the battery from the positive terminal: A is positive and B is negative.
AnswerA: positive; B: negative

(iii)(b) State the effect on the magnetic field if an iron rod is held along the axis of the coil.

  1. Soft iron is magnetised by the coil's field and concentrates the field lines through it, so the magnetic field becomes much stronger.
AnswerThe magnetic field becomes stronger.

(iii)(c)(1) State one way to change the polarity of the coil.

  1. The polarity depends on the direction of the current: interchange the battery connections at A and B to reverse the current through the coil.
AnswerReverse the current (interchange the terminals at A and B).

(iii)(c)(2) State one way to decrease the strength of the magnetic field around the coil.

  1. The field is proportional to the current: decrease the current, for example by increasing the resistance of the rheostat (or use fewer turns).
AnswerDecrease the current through the coil (increase the rheostat's resistance).
Ask about this question

Questions are quoted from the ICSE 2025 Physics Specimen Question Paper (521); figures are described in words. Every final answer is checked against the official CISCE answers. Where a question offers a choice, every option is solved.

CISCE specimen question papers and their answers are referenced for educational and review purposes only, under fair dealing. All copyrights in the questions belong to the Council for the Indian School Certificate Examinations. Solutions and explanations provided here are original works by Your Abhyaasika, generated with AI, and may contain mistakes. Your Abhyaasika is not affiliated with CISCE.