AI-generated solutions. The solutions and explanations on this page are written by AI. We check the final answers with automated tests, but AI can still make mistakes, especially in explanations and in figures described in words. If something looks wrong, ask in the doubt chat on that question or check with your teacher.

ICSE Class 10 Physics Specimen Paper 2026 with Solutions

Step-by-step solutions to every question of the ICSE 2026 Specimen Question Paper in Physics (Science Paper 1, subject code 521) for Class 10: the fifteen multiple-choice items and short answers of Section A, and all six questions of Section B, of which the exam asks for any four. Each answer is written the way the ICSE marking scheme awards marks (formula, substitution, result with units), and every answer is checked against the official CISCE draft marking scheme for the specimen; where the scheme's working slips, the page follows the physics and says so.

ICSE 2026 Physics Specimen Question Paper (521): 23 questions, 80 marks, 2 hours. Open any question to see the steps one at a time or ask a doubt about a step. Also solved: Physics Specimen Paper 2025.

Section A: 40 marks: attempt all questions from this section

Q1 (i)

Question 1 (i) (1 mark)

Force and moments
A moment of couple has a tendency to rotate the body in an anticlockwise direction. The moment of couple is taken as:
  1. (A)positive
  2. (B)negative
  3. (C)maximum
  4. (D)zero

Tests: Sign convention for the moment of a force or couple.

Show solution
  1. Sign convention for moments: an anticlockwise moment is taken as positive, a clockwise moment as negative.
Answer(a) positive
Ask about this question
Q1 (ii)

Question 1 (ii) (1 mark)

Work, energy and power
The kinetic energy of a given body depends on the:
  1. (A)position
  2. (B)centre of gravity
  3. (C)momentum
  4. (D)displacement

Tests: Relation between kinetic energy and momentum.

Show solution
  1. K=12mv2=p22mK = \dfrac{1}{2}mv^2 = \dfrac{p^2}{2m}, where p=mvp = mv is the momentum.
  2. For a given body (fixed m) the kinetic energy depends only on its momentum (speed). Position decides potential energy, not kinetic energy.
Answer(c) momentum
Ask about this question
Q1 (iii)

Question 1 (iii) (1 mark)

Work, energy and power
During power production in a coal-based thermoelectric power plant, the correct sequence of energy conversions taking place is:
  1. (A)heat →\to mechanical →\to chemical
  2. (B)heat →\to mechanical →\to electrical
  3. (C)chemical →\to heat →\to light
  4. (D)heat →\to chemical →\to electrical

Tests: Energy conversions in a thermal power station.

Show solution
  1. Burning coal gives heat, which turns water into steam; the steam turns the turbine (mechanical energy); the turbine drives the generator (electrical energy).
  2. Among the options the matching chain is heat →\to mechanical →\to electrical.

    Why: The full chain starts with chemical energy of coal, but no option lists four stages.

Answer(b) heat →\to mechanical →\to electrical
Ask about this question
Q1 (iv)

Question 1 (iv) (1 mark)

Machines
Anita used a single movable pulley to lift a bucket of water from a well. She lubricates the pulley. Which of the following statements is true regarding the performance of the pulley used?
  1. (A)Mechanical Advantage decreases and efficiency increases.
  2. (B)Velocity Ratio increases and efficiency decreases.
  3. (C)Mechanical Advantage remains unchanged and efficiency increases.
  4. (D)Velocity Ratio remains unchanged and efficiency increases.

Tests: Effect of friction on M.A., V.R. and efficiency.

Show solution
  1. Velocity ratio depends only on how the pulley is set up (distances moved), so it stays 2 for a single movable pulley.
  2. Lubrication reduces friction, so less effort is needed: M.A. increases, and efficiency η=M.A.V.R.\eta = \dfrac{\text{M.A.}}{\text{V.R.}} increases.
Answer(d) Velocity Ratio remains unchanged and efficiency increases
Ask about this question
Q1 (v)

Question 1 (v) (1 mark)

Refraction through a prism
Inside the prism, during the dispersion of white light, compared to blue, red light:
  1. (A)slows down less and refracts more.
  2. (B)slows down more and refracts less.
  3. (C)slows down more and refracts more.
  4. (D)slows down less and refracts less.

Tests: Dispersion: refractive index and speed depend on colour.

Show solution
  1. Glass has a smaller refractive index for red than for blue: μred<μblue\mu_{red} < \mu_{blue}.
  2. Speed in glass v=c/μv = c/\mu, so red travels faster (slows down less), and with a smaller μ\mu it bends (deviates) less.
Answer(d) slows down less and refracts less
Ask about this question
Q1 (vi)

Question 1 (vi) (1 mark)

Refraction of light
When objects are viewed through the rising heat of a campfire they appear to shimmer. The optical phenomenon responsible for this effect is:
  1. (A)refraction
  2. (B)reflection
  3. (C)scattering
  4. (D)total internal reflection

Tests: Atmospheric refraction in daily life.

Show solution
  1. Hot air above the fire is less dense and its density keeps changing, so its refractive index changes from place to place and moment to moment.
  2. Light from the objects bends by varying amounts as it passes through, so the objects appear to waver: refraction.
Answer(a) refraction
Ask about this question
Q1 (vii)

Question 1 (vii) (1 mark)

Lenses
A convex lens with a focal length of 12 cm has an object at a distance of 20 cm in front of the lens. A blurred image is obtained on the screen placed at a distance of 23 cm in front of the lens. In order to obtain a clear image, the screen has to be moved:
  1. (A)towards the lens.
  2. (B)away from the lens.
  3. (C)to a position very far from the lens.
  4. (D)either towards or away from the lens.

Tests: Locate a real image with the lens formula.

Show solution
  1. Lens formula 1v−1u=1f\dfrac{1}{v} - \dfrac{1}{u} = \dfrac{1}{f} with u=−20u = -20 cm, f=+12f = +12 cm.
  2. 1v=112−120=5−360=130\dfrac{1}{v} = \dfrac{1}{12} - \dfrac{1}{20} = \dfrac{5 - 3}{60} = \dfrac{1}{30}, so v=30v = 30 cm.
  3. The sharp image is 30 cm from the lens; the screen is at 23 cm, so it must move 7 cm away from the lens.
Answer(b) away from the lens
Ask about this question
Q1 (viii)

Question 1 (viii) (1 mark)

Scattering of light
Assertion (A): Soldiers avoid firing at a target in foggy weather conditions. Reason (R): In foggy weather, light gets scattered by tiny water droplets, reducing visibility.
  1. (A)(A) is true but (R) is false.
  2. (B)(A) is false but (R) is true.
  3. (C)Both (A) and (R) are true and (R) is the correct explanation of (A).
  4. (D)Both (A) and (R) are true, but (R) is not the correct explanation of (A).

Tests: Scattering of light by fog and its effect on visibility.

Show solution
  1. Fog droplets scatter light strongly in all directions, so little light from the target reaches the eye: visibility is poor. (R) is true.
  2. With the target hard to see, aiming is unreliable, so firing is avoided. (A) is true and (R) is exactly why.
Answer(c) Both (A) and (R) are true and (R) is the correct explanation of (A)
Ask about this question
Q1 (ix)

Question 1 (ix) (1 mark)

Sound
Two sound waves X and Y have the same amplitude and the same wave pattern but their frequencies are 60 Hz and 120 Hz respectively, then:
  1. (A)X will be shriller and Y will be grave.
  2. (B)X will be grave and Y will be shriller.
  3. (C)X will differ in quality than Y.
  4. (D)X is louder than Y.

Tests: Characteristics of sound: pitch, loudness and quality.

Show solution
  1. Pitch depends on frequency: the higher the frequency, the shriller the sound.
  2. Y (120 Hz) is shriller; X (60 Hz) is grave. Same amplitude means same loudness; same wave pattern means same quality.
Answer(b) X will be grave and Y will be shriller
Ask about this question
Q1 (x)

Question 1 (x) (1 mark)

Current electricity
In the circuit given below, identify the correct relation between the currents flowing through the 2 Ω, 3 Ω, and 5 Ω resistors. (Figure: a 12 V battery is connected across two branches in parallel: one branch has the 3 Ω and 2 Ω resistors in series, the other has the 5 Ω resistor alone.)
  1. (A)current through 2 Ω2\,\Omega > current through 3 Ω3\,\Omega
  2. (B)current through 5 Ω5\,\Omega < current through 3 Ω3\,\Omega
  3. (C)current through 2 Ω2\,\Omega = current through 5 Ω5\,\Omega
  4. (D)current through 5 Ω5\,\Omega > current through 3 Ω3\,\Omega

Tests: Currents in series and parallel combinations.

Show solution
  1. Branch 1: 3+2=5 Ω3 + 2 = 5\,\Omega; current =125=2.4= \dfrac{12}{5} = 2.4 A, the same through the 3 Ω and the 2 Ω (series).
  2. Branch 2: 125=2.4\dfrac{12}{5} = 2.4 A through the 5 Ω.
  3. So the currents through the 2 Ω, 3 Ω and 5 Ω are all 2.4 A; only (c) is true.
Answer(c) current through 2 Ω2\,\Omega = current through 5 Ω5\,\Omega
Ask about this question
Q1 (xi)

Question 1 (xi) (1 mark)

Household circuits
According to the old convention, the colour of the earth wire is:
  1. (A)black
  2. (B)green
  3. (C)yellow
  4. (D)red

Tests: Colour coding of household wires.

Show solution
  1. Old convention: live red, neutral black, earth green. (New convention: live brown, neutral light blue, earth green or green-yellow.)
Answer(b) green
Ask about this question
Q1 (xii)

Question 1 (xii) (1 mark)

Transformers
For an ideal step up transformer:
  1. (A)VoltageprimaryVoltagesecondary>1\dfrac{\text{Voltage}_{primary}}{\text{Voltage}_{secondary}} > 1
  2. (B)CurrentprimaryCurrentsecondary<1\dfrac{\text{Current}_{primary}}{\text{Current}_{secondary}} < 1
  3. (C)number of turnsprimarynumber of turnssecondary=1\dfrac{\text{number of turns}_{primary}}{\text{number of turns}_{secondary}} = 1
  4. (D)powerprimarypowersecondary=1\dfrac{\text{power}_{primary}}{\text{power}_{secondary}} = 1

Tests: Voltage, current and power in an ideal step-up transformer.

Show solution
  1. Step up: Vs>VpV_s > V_p and Ns>NpN_s > N_p, so Vp/Vs<1V_p/V_s < 1 and Np/Ns<1N_p/N_s < 1: (a) and (c) are false.
  2. Ideal transformer: no energy loss, so VpIp=VsIsV_pI_p = V_sI_s; power ratio =1= 1, and Ip/Is=Vs/Vp>1I_p/I_s = V_s/V_p > 1: (b) is false, (d) is true.
Answer(d) powerprimarypowersecondary=1\dfrac{\text{power}_{primary}}{\text{power}_{secondary}} = 1
Ask about this question
Q1 (xiii)

Question 1 (xiii) (1 mark)

Calorimetry
Heat capacity of a body is the:
  1. (A)energy needed to melt a body without change in its temperature.
  2. (B)energy needed to raise the temperature of a body by 1°C.
  3. (C)increase in volume of the body when its temperature increases by 1°C.
  4. (D)total amount of internal energy that is constant.

Tests: Definition of heat capacity.

Show solution
  1. Heat capacity C′=QΔTC' = \dfrac{Q}{\Delta T}: the heat needed to raise the temperature of the whole body by 1 °C (or 1 K). Unit J K⁻¹.
Answer(b) energy needed to raise the temperature of a body by 1°C
Ask about this question
Q1 (xiv)

Question 1 (xiv) (1 mark)

Calorimetry
The amount of heat energy required to melt a given mass of a substance at its melting point, without any rise in its temperature is called the:
  1. (A)specific heat capacity.
  2. (B)specific latent heat of fusion.
  3. (C)latent heat of fusion.
  4. (D)specific latent heat of freezing.

Tests: Latent heat versus specific latent heat.

Show solution
  1. For a given mass (any mass) the heat to melt it at constant temperature is its latent heat of fusion, L = mℓ.
  2. Specific latent heat of fusion is the same quantity per unit mass (1 kg); the question says a given mass, so (c).
Answer(c) latent heat of fusion
Ask about this question
Q1 (xv)

Question 1 (xv) (1 mark)

Radioactivity
A nucleus of an atom consists of 146 neutrons and 95 protons. It decays after emitting an alpha particle. How many protons and neutrons are left in the nucleus after an alpha emission?
  1. (A)protons = 93, neutrons = 142
  2. (B)protons = 95, neutrons = 144
  3. (C)protons = 93, neutrons = 144
  4. (D)protons = 95, neutrons = 142

Tests: Change in proton and neutron numbers in alpha decay.

Show solution
  1. An alpha particle is a helium nucleus 24He^4_2\text{He}: 2 protons and 2 neutrons.
  2. Protons: 95−2=9395 - 2 = 93. Neutrons: 146−2=144146 - 2 = 144.
Answer(c) protons = 93, neutrons = 144
Ask about this question
Q2

Question 2 (10 marks)

Short answers: machines, waves, heat, sound, electricity, nuclear energy
(i) Complete the following by choosing the correct answers from the bracket. (ii) Match the movement of the body part in Column A to the class of lever in Column B. (iii) Echo depth sounding.
  1. (i)(a)
    A ________ [Class II / Class III] lever will always have M.A. > 1.
  2. (i)(b)
    A boy uses a GPS device to locate his missing friend in a crowded area; the system primarily uses ________ [ultraviolet waves / microwaves] to track the location.
  3. (i)(c)
    Unit of specific heat capacity is ________. [kg2m2s−2K−1\text{kg}^2\text{m}^2\text{s}^{-2}\text{K}^{-1} / m2s−2K−1\text{m}^2\text{s}^{-2}\text{K}^{-1}]
  4. (i)(d)
    The threshold of hearing is ________. [0 dB, 20 Hz]
  5. (i)(e)
    Two copper wires can have different resistivity if they have different ________. [lengths / temperatures]
  6. (i)(f)
    The reaction responsible for the production of energy in the sun is ________. [Nuclear Fusion / Nuclear Fission]
  7. (ii)(a)
    Nodding head: which class of lever (Class III, Class II, Class I)?
  8. (ii)(b)
    Lifting body weight on your toes: which class of lever?
  9. (iii)(a)
    Name the wave used for echo depth sounding.
  10. (iii)(b)
    Give one reason why the waves mentioned in (a) are used for the above purpose.

Tests: Recall key facts across the syllabus: levers, waves, units, sound, resistivity, nuclear energy.

Show solution

(i)(a) A ________ [Class II / Class III] lever will always have M.A. > 1.

  1. In a class II lever the load is between the fulcrum and the effort, so the effort arm is always longer than the load arm.
  2. M.A. =effort armload arm>1= \dfrac{\text{effort arm}}{\text{load arm}} > 1 always. (A class III lever always has M.A. < 1.)
AnswerClass II

(i)(b) A boy uses a GPS device to locate his missing friend in a crowded area; the system primarily uses ________ [ultraviolet waves / microwaves] to track the location.

  1. GPS satellites send signals in the microwave band (around 1.2 to 1.6 GHz), which pass through the atmosphere and clouds; ultraviolet is absorbed by the atmosphere.
Answermicrowaves

(i)(c) Unit of specific heat capacity is ________. [kg2m2s−2K−1\text{kg}^2\text{m}^2\text{s}^{-2}\text{K}^{-1} / m2s−2K−1\text{m}^2\text{s}^{-2}\text{K}^{-1}]

  1. SI unit: J kg−1K−1\text{J kg}^{-1}\text{K}^{-1}, with 1 J=1 kg m2s−21\text{ J} = 1\text{ kg m}^2\text{s}^{-2}.
  2. kg m2s−2kg K=m2s−2K−1\dfrac{\text{kg m}^2\text{s}^{-2}}{\text{kg K}} = \text{m}^2\text{s}^{-2}\text{K}^{-1}.
Answerm2s−2K−1\text{m}^2\text{s}^{-2}\text{K}^{-1}

(i)(d) The threshold of hearing is ________. [0 dB, 20 Hz]

  1. The threshold of hearing is the faintest sound a normal ear can hear; on the decibel scale it is the zero level, 0 dB. (20 Hz is the lower limit of audible frequency, not the threshold of hearing.)
Answer0 dB

(i)(e) Two copper wires can have different resistivity if they have different ________. [lengths / temperatures]

  1. Resistivity depends only on the material and its temperature, not on length or thickness. Same material (copper), so only a temperature difference changes it.
Answertemperatures

(i)(f) The reaction responsible for the production of energy in the sun is ________. [Nuclear Fusion / Nuclear Fission]

  1. In the sun's core, hydrogen nuclei fuse to form helium, releasing energy: nuclear fusion.
AnswerNuclear fusion

(ii)(a) Nodding head: which class of lever (Class III, Class II, Class I)?

  1. The fulcrum (the joint of the skull with the backbone) lies between the load (weight of the face at the front) and the effort (neck muscles at the back): class I.
AnswerNodding head: Class I

(ii)(b) Lifting body weight on your toes: which class of lever?

  1. The fulcrum is at the toes, the load (body weight) acts in between, and the effort (calf muscles) acts at the heel: load between fulcrum and effort, class II.
AnswerLifting body weight on your toes: Class II

(iii)(a) Name the wave used for echo depth sounding.

  1. SONAR uses sound of frequency above 20 kHz: ultrasonic waves.
AnswerUltrasonic waves

(iii)(b) Give one reason why the waves mentioned in (a) are used for the above purpose.

  1. Ultrasonic waves have a very short wavelength, so they can be sent as a narrow beam that travels long distances without spreading (deviating) much, and they are not easily absorbed by water.
AnswerThey can be sent as a narrow beam that travels long distances without much deviation and is not easily absorbed.
Ask about this question
Q3

Question 3 (15 marks)

Short answers: lenses, electrical energy, centre of gravity, heat, magnetism, radioactivity, light
Question 3 has seven short parts, (i) to (vii).
  1. (i)(a)
    A lens is made of two materials of different refractive indices (μ1, μ2): the upper half of a biconvex lens (above the principal axis) is of μ1 and the lower half of μ2. If the rays are coming from a distant object, then how many images will be seen?
  2. (i)(b)
    A glass lens always forms a virtual, erect, and diminished image of an object kept in front of it. Identify the lens.
  3. (ii)
    Two kilowatt-hour meter readings: first 00856 kWh, later 01567 kWh. Assuming a continuously running 2000 W air conditioner as the sole electrical device in use, calculate the time interval, in hours, between these two meter readings.
  4. (iii)(a)
    ABCDE is a regular pentagon with its centre of gravity at O (vertex A at the bottom, D and C at the top, E on the left and B on the right). On the vertical line through A and O, Z is just above O and X is just below O, inside the bottom triangle PAQ; Y lies to the right of O towards B; W is near vertex D. PQ is a horizontal line just below E and B. What will be the most probable position (W, X, Y, Z or O) of the new centre of gravity if a piece of clay is attached at point A?
  5. (iii)(b)
    What will be the most probable position of the new centre of gravity if the pentagon is cut along the line PQ (of the remaining part DCBQPE)?
  6. (iv)
    A solid of mass 60 g at 100 °C is placed in 150 g of water at 20 °C. The final steady temperature is 25 °C. Calculate the heat capacity of the solid. [sp. heat capacity of water = 4.2 J g−1K−1\text{J g}^{-1}\text{K}^{-1}]
  7. (v)(a)
    A copper wire is wound around a U-shaped soft iron bar; its ends are A and B. An iron pin is brought near. First Source P (an AC source) and then Source Q (a DC cell) are connected across AB, each operating independently. State True or False: Source P as well as Source Q, when connected across AB, can attract the iron pin.
  8. (v)(b)
    Justify your answer to (a) with a suitable reason.
  9. (vi)(a)
    Name the radiation that is emitted during the decay of a nucleus that has the highest penetrating power.
  10. (vi)(b)
    Does the emission of the above-mentioned radiation result in a change in the mass number?
  11. (vii)(a)
    Advanced optical sensors in air-to-air missiles use fiber optic cables to transmit light signals with minimal loss. Name the optical phenomenon that allows light signals to remain confined within the fiber optic cables during transmission.
  12. (vii)(b)
    Explain the two main conditions necessary for this phenomenon to occur.

Tests: Apply core ideas: lens images, kWh, centre of gravity, principle of mixtures, electromagnets, gamma rays, total internal reflection.

Show solution

(i)(a) A lens is made of two materials of different refractive indices (μ1, μ2): the upper half of a biconvex lens (above the principal axis) is of μ1 and the lower half of μ2. If the rays are coming from a distant object, then how many images will be seen?

  1. Focal length depends on the refractive index of the lens material, so the two halves have different focal lengths.
  2. Each half forms its own image of the distant object at its own focus: two images.
Answer2 images

(i)(b) A glass lens always forms a virtual, erect, and diminished image of an object kept in front of it. Identify the lens.

  1. A concave lens forms a virtual, erect, diminished image for every position of the object; a convex lens gives a magnified virtual image only when the object is inside F.
AnswerConcave lens

(ii) Two kilowatt-hour meter readings: first 00856 kWh, later 01567 kWh. Assuming a continuously running 2000 W air conditioner as the sole electrical device in use, calculate the time interval, in hours, between these two meter readings.

  1. Energy used = 1567 − 856 = 711 kWh.
  2. Power = 2000 W = 2 kW; time t=EP=711 kWh2 kW=355.5t = \dfrac{E}{P} = \dfrac{711\text{ kWh}}{2\text{ kW}} = 355.5 h.
Answer355.5 hours

(iii)(a) ABCDE is a regular pentagon with its centre of gravity at O (vertex A at the bottom, D and C at the top, E on the left and B on the right). On the vertical line through A and O, Z is just above O and X is just below O, inside the bottom triangle PAQ; Y lies to the right of O towards B; W is near vertex D. PQ is a horizontal line just below E and B. What will be the most probable position (W, X, Y, Z or O) of the new centre of gravity if a piece of clay is attached at point A?

  1. Extra mass at A pulls the centre of gravity from O towards A, along the line OA.
  2. The point on OA just below O is X.
AnswerX

(iii)(b) What will be the most probable position of the new centre of gravity if the pentagon is cut along the line PQ (of the remaining part DCBQPE)?

  1. Cutting along PQ removes the triangle PAQ at the bottom, so the remaining mass lies higher.
  2. The figure is still symmetric about the vertical line through A and O, so the new centre of gravity moves up along that line from O: Z.
AnswerZ

(iv) A solid of mass 60 g at 100 °C is placed in 150 g of water at 20 °C. The final steady temperature is 25 °C. Calculate the heat capacity of the solid. [sp. heat capacity of water = 4.2 J g−1K−1\text{J g}^{-1}\text{K}^{-1}]

  1. Principle of mixtures: heat lost by the solid = heat gained by the water.
  2. Heat gained by water =mcΔT=150×4.2×(25−20)=3150= mc\Delta T = 150 \times 4.2 \times (25 - 20) = 3150 J.
  3. Heat lost by solid =C′×(100−25)=75 C′= C' \times (100 - 25) = 75\,C'. So 75 C′=315075\,C' = 3150, C′=42 J K−1C' = 42\ \text{J K}^{-1}.
AnswerHeat capacity of the solid =42 J K−1= 42\ \text{J K}^{-1}

(v)(a) A copper wire is wound around a U-shaped soft iron bar; its ends are A and B. An iron pin is brought near. First Source P (an AC source) and then Source Q (a DC cell) are connected across AB, each operating independently. State True or False: Source P as well as Source Q, when connected across AB, can attract the iron pin.

  1. Any current in the coil magnetises the soft iron core, so the electromagnet attracts the pin with either source.
AnswerTrue

(v)(b) Justify your answer to (a) with a suitable reason.

  1. Both AC and DC currents produce a magnetic field around the coil, which magnetises the soft iron.
  2. With AC the poles keep reversing, but the pin is magnetised by induction with opposite polarity each time, so it is always attracted.
AnswerBoth AC and DC currents produce a magnetic field, which magnetises the soft iron; an iron pin is attracted whatever the polarity.

(vi)(a) Name the radiation that is emitted during the decay of a nucleus that has the highest penetrating power.

  1. Penetrating power: alpha < beta < gamma. Gamma rays are uncharged electromagnetic waves of very short wavelength.
AnswerGamma (γ\gamma) radiation

(vi)(b) Does the emission of the above-mentioned radiation result in a change in the mass number?

  1. A gamma ray is a photon with no mass and no charge: the nucleus only loses energy, so A and Z stay the same.
AnswerNo, the mass number does not change.

(vii)(a) Advanced optical sensors in air-to-air missiles use fiber optic cables to transmit light signals with minimal loss. Name the optical phenomenon that allows light signals to remain confined within the fiber optic cables during transmission.

  1. Light inside the fibre strikes the core-cladding boundary at more than the critical angle and is reflected back again and again: total internal reflection.
AnswerTotal internal reflection

(vii)(b) Explain the two main conditions necessary for this phenomenon to occur.

  1. 1. Light must travel from an optically denser medium to an optically rarer medium (fibre core to cladding).
  2. 2. The angle of incidence in the denser medium must be greater than the critical angle for the pair of media.
AnswerLight goes from denser to rarer medium, and the angle of incidence exceeds the critical angle.
Ask about this question

Section B: 40 marks: attempt any four questions from this section

Q4

Question 4 (10 marks)

Refraction, lenses and the spectrum
Question 4: (i) image of a fish; lens in liquids, (ii) real and apparent depth, (iii) dispersion by a lens and ultraviolet radiation.
  1. (i)(a)
    A photograph shows a fish in a tank and, above it, an inverted image of the fish seen on the surface of water (viewed from below). Name the phenomenon responsible for the formation of this image.
  2. (i)(b)(1)
    A double convex lens with refractive index μ1 is placed in liquid 1 of refractive index μ3 (Figure a), with μ1 > μ3. How would a parallel incident beam of light refract when it comes out of the lens?
  3. (i)(b)(2)
    The same lens (μ1) is placed in liquid 2 of refractive index μ2 (Figure b), with μ2 > μ1. How would a parallel incident beam of light refract when it comes out of the lens?
  4. (ii)(a)
    A scientist lowers a metallic ruler vertically into a transparent oil tank. The ruler touches an object placed at the bottom of the tank and gets wet up to the 25 cm mark. If the refractive index of the glycerin is 1.25, up to which mark will the ruler get wet if the scientist lowers it up to the image of the object?
  5. (ii)(b)
    How will this length in (a) change if another liquid of μ > 1.25 is used?
  6. (iii)(a)
    A mixture of red, blue, and green light rays is passed through a convex lens, as a single ray parallel to the principal axis. State whether the ray passes through a single point or through different points on the principal axis after refraction.
  7. (iii)(b)
    Name the invisible radiation which is studied using the quartz prism.
  8. (iii)(c)
    State one use of the radiation mentioned by you in (b) above.
  9. (iii)(d)
    Name one type of radiation with a wavelength greater than that of the radiation mentioned by you in (b) above.

Tests: Total internal reflection, lens behaviour in a medium, apparent depth, dispersion and ultraviolet radiation.

Show solution

(i)(a) A photograph shows a fish in a tank and, above it, an inverted image of the fish seen on the surface of water (viewed from below). Name the phenomenon responsible for the formation of this image.

  1. Light from the fish travels upward in water (denser) and meets the water-air surface at an angle greater than the critical angle (about 49°).
  2. It is totally reflected back into the water, so the surface acts as a mirror and the fish's image is seen at the surface: total internal reflection.
AnswerTotal internal reflection

(i)(b)(1) A double convex lens with refractive index μ1 is placed in liquid 1 of refractive index μ3 (Figure a), with μ1 > μ3. How would a parallel incident beam of light refract when it comes out of the lens?

  1. A lens behaves as it does in air when it is optically denser than the surrounding medium.
  2. Here μ1 > μ3, so the double convex lens still acts as a converging lens (with a longer focal length than in air): the beam converges.
AnswerThe beam converges.

(i)(b)(2) The same lens (μ1) is placed in liquid 2 of refractive index μ2 (Figure b), with μ2 > μ1. How would a parallel incident beam of light refract when it comes out of the lens?

  1. Now the lens is optically rarer than the liquid, so rays bend away from the normal on entering and the bending is reversed.
  2. The double convex lens acts as a diverging lens: the beam diverges.
AnswerThe beam diverges.

(ii)(a) A scientist lowers a metallic ruler vertically into a transparent oil tank. The ruler touches an object placed at the bottom of the tank and gets wet up to the 25 cm mark. If the refractive index of the glycerin is 1.25, up to which mark will the ruler get wet if the scientist lowers it up to the image of the object?

  1. The wet length is the real depth: 25 cm. The image of the object is at the apparent depth.
  2. μ=real depthapparent depth\mu = \dfrac{\text{real depth}}{\text{apparent depth}}, so apparent depth =251.25=20= \dfrac{25}{1.25} = 20 cm.
  3. Lowered only to the image, the ruler is wet up to the 20 cm mark.
AnswerUp to the 20 cm mark

(ii)(b) How will this length in (a) change if another liquid of μ > 1.25 is used?

  1. Apparent depth =real depthμ= \dfrac{\text{real depth}}{\mu}: a larger μ\mu gives a smaller apparent depth, so the image is higher and the wet length is less.
AnswerThe length decreases.

(iii)(a) A mixture of red, blue, and green light rays is passed through a convex lens, as a single ray parallel to the principal axis. State whether the ray passes through a single point or through different points on the principal axis after refraction.

  1. The lens has a different refractive index for each colour (μblue>μgreen>μred\mu_{blue} > \mu_{green} > \mu_{red}), so each colour has its own focal length.
  2. Blue is bent most and meets the axis nearest the lens, red farthest: the colours cross the axis at different points (chromatic aberration).
AnswerThrough different points.

(iii)(b) Name the invisible radiation which is studied using the quartz prism.

  1. Ordinary glass absorbs ultraviolet radiation, but quartz transmits it, so a quartz prism is used for ultraviolet.
AnswerUltraviolet radiation

(iii)(c) State one use of the radiation mentioned by you in (b) above.

  1. Ultraviolet radiation kills germs, so it is used to sterilise water, surgical instruments and food. (Also: detecting purity of gems and eggs; producing vitamin D in the skin.)
AnswerSterilisation (killing germs in water, instruments and food).

(iii)(d) Name one type of radiation with a wavelength greater than that of the radiation mentioned by you in (b) above.

  1. Spectrum in order of increasing wavelength: gamma, X-rays, ultraviolet, visible, infrared, microwaves, radio waves. Any one after ultraviolet.
AnswerInfrared radiation (or visible light, microwaves, radio waves).
Ask about this question
Q5

Question 5 (10 marks)

Lenses and calorimetry
Question 5: (i) image by a convex lens, (ii) cooling curve, (iii) temperature of a flame by the method of mixtures.
  1. (i)(a)
    An object is placed at a distance of 24 cm in front of a convex lens of focal length 8 cm. What is the nature of the image so formed?
  2. (i)(b)
    Calculate the distance of the image from the lens.
  3. (ii)(a)
    A cooling curve for a substance X (temperature in °C against time) is flat at 150 °C from the start, then falls in a straight line to 60 °C, stays flat at 60 °C, and then falls more steeply to 10 °C. State the temperatures at which the substance condenses.
  4. (ii)(b)
    Mention the temperature range in which the substance is in its liquid state.
  5. (ii)(c)
    State True or False: The amount of heat released when a substance is cooled by 10 °C in its liquid state is greater than the heat released when it is cooled by the same amount in its solid state.
  6. (iii)
    In an experiment to measure the temperature of the flame of a Bunsen burner, a lump of copper of mass 0.12 kg is heated on the flame for a long time. The copper is then quickly transferred into a beaker of negligible heat capacity containing 0.84 kg of water and the temperature of the water rose from 15 °C to 35 °C. Calculate the temperature of the flame. [sp. heat capacity of copper = 0.4 J g−1 ∘C−1\text{J g}^{-1}\,{}^\circ\text{C}^{-1}, of water = 4.2 J g−1 ∘C−1\text{J g}^{-1}\,{}^\circ\text{C}^{-1}]

Tests: Lens formula and image nature; reading a cooling curve; principle of mixtures.

Show solution

(i)(a) An object is placed at a distance of 24 cm in front of a convex lens of focal length 8 cm. What is the nature of the image so formed?

  1. The object is beyond 2F (24 cm > 2f = 16 cm), so the image is formed between F and 2F on the other side: real, inverted and diminished.
AnswerReal, inverted (and diminished)

(i)(b) Calculate the distance of the image from the lens.

  1. 1v−1u=1f\dfrac{1}{v} - \dfrac{1}{u} = \dfrac{1}{f} with u=−24u = -24 cm, f=+8f = +8 cm.
  2. 1v=18+1−24=3−124=112\dfrac{1}{v} = \dfrac{1}{8} + \dfrac{1}{-24} = \dfrac{3 - 1}{24} = \dfrac{1}{12}
  3. v=+12v = +12 cm: 12 cm from the lens on the side opposite the object.
Answer12 cm from the lens (on the other side)

(ii)(a) A cooling curve for a substance X (temperature in °C against time) is flat at 150 °C from the start, then falls in a straight line to 60 °C, stays flat at 60 °C, and then falls more steeply to 10 °C. State the temperatures at which the substance condenses.

  1. Flat stretches are changes of state at constant temperature. The first one, at 150 °C, is the gas turning into liquid: condensation.
Answer150 °C

(ii)(b) Mention the temperature range in which the substance is in its liquid state.

  1. Between condensation at 150 °C and freezing (the second flat stretch) at 60 °C the substance is a liquid.
AnswerFrom 150 °C down to 60 °C

(ii)(c) State True or False: The amount of heat released when a substance is cooled by 10 °C in its liquid state is greater than the heat released when it is cooled by the same amount in its solid state.

  1. Heat released Q = mcΔT, so for the same m and ΔT the state with the larger specific heat capacity releases more heat.
  2. On the curve the liquid cools more slowly (gentler slope) than the solid (steeper final stretch) while losing heat at a similar rate, so the liquid's specific heat capacity is larger, as it usually is (water 4200, ice 2100 J kg⁻¹ K⁻¹).
AnswerTrue

(iii) In an experiment to measure the temperature of the flame of a Bunsen burner, a lump of copper of mass 0.12 kg is heated on the flame for a long time. The copper is then quickly transferred into a beaker of negligible heat capacity containing 0.84 kg of water and the temperature of the water rose from 15 °C to 35 °C. Calculate the temperature of the flame. [sp. heat capacity of copper = 0.4 J g−1 ∘C−1\text{J g}^{-1}\,{}^\circ\text{C}^{-1}, of water = 4.2 J g−1 ∘C−1\text{J g}^{-1}\,{}^\circ\text{C}^{-1}]

  1. After a long time on the flame the copper is at the flame's temperature tt. In SI: cCu=400c_{Cu} = 400, cw=4200 J kg−1 ∘C−1c_w = 4200\ \text{J kg}^{-1}\,{}^\circ\text{C}^{-1}.
  2. Heat lost by copper =0.12×400×(t−35)=48(t−35)= 0.12 \times 400 \times (t - 35) = 48(t - 35) J.
  3. Heat gained by water =0.84×4200×(35−15)=70 560= 0.84 \times 4200 \times (35 - 15) = 70\,560 J.
  4. 48(t−35)=70 560⇒t−35=1470⇒t=1505 ∘C48(t - 35) = 70\,560 \Rightarrow t - 35 = 1470 \Rightarrow t = 1505\ ^\circ\text{C}.
AnswerTemperature of the flame = 1505 °C
Ask about this question
Q6

Question 6 (10 marks)

Moments, work and energy
Question 6: (i) a non-uniform rod balanced off-centre, (ii) sign of work done by gravity, (iii) energy of a mass sliding on a hemispherical cup.
  1. (i)(a)
    A metal rod AB of length 80 cm is balanced at 45 cm from the end A with 100 gf weights suspended from the two ends (A at 0 cm, centre C at 40 cm, fulcrum at 45 cm, B at 80 cm). If this rod is cut at the centre C, then compare the weight of AC to the weight of BC. (Use >, < or =)
  2. (i)(b)
    Give a reason for your answer in (a).
  3. (ii)(a)
    State whether the work done by gravity is positive, negative, or zero: A person walks on a levelled road.
  4. (ii)(b)
    A person climbs a ladder.
  5. (ii)(c)
    A car in a neutral gear is coming down the slope.
  6. (iii)(a)
    A, B, C and D are four points on a hemispherical cup placed inverted on the ground: A is the top, B and C the ends of the diameter BC = 360 cm on the ground, and D is a point on the surface at the level of E, where E is on the vertical radius below A with AE = R/3 (R is the radius of the cup). A small spherical mass 500 g at rest at the point A slides down along the smooth surface of the cup. Assuming no loss of energy (g = 10 m s⁻²), calculate its potential energy at A relative to B.
  7. (iii)(b)
    Calculate its speed at the point B (lowest point).
  8. (iii)(c)
    Calculate its kinetic energy at D.

Tests: Principle of moments for a non-uniform rod; sign of work; conservation of mechanical energy.

Show solution

(i)(a) A metal rod AB of length 80 cm is balanced at 45 cm from the end A with 100 gf weights suspended from the two ends (A at 0 cm, centre C at 40 cm, fulcrum at 45 cm, B at 80 cm). If this rod is cut at the centre C, then compare the weight of AC to the weight of BC. (Use >, < or =)

  1. Moments of the two 100 gf weights about the fulcrum: at A, 100 × 45 = 4500 gf cm anticlockwise; at B, 100 × 35 = 3500 gf cm clockwise.
  2. For balance the rod's own weight must supply 1000 gf cm clockwise, so its centre of gravity lies on the B side of the fulcrum, beyond 45 cm (beyond the centre C at 40 cm).
  3. More of the rod's mass is in CB than in AC.
AnswerWeight of AC < weight of BC

(i)(b) Give a reason for your answer in (a).

  1. The two end weights are equal, but the moment arm of B (35 cm) is shorter than that of A (45 cm), so they alone would tip the rod towards A.
  2. The rod balances only because the moment of its own weight acts on the B side: its centre of gravity lies beyond the 45 cm mark, past the midpoint C, so the rod is non-uniform with more weight between C and B.
AnswerThe rod's centre of gravity lies beyond C on the B side, so more of its weight is in CB.

(ii)(a) State whether the work done by gravity is positive, negative, or zero: A person walks on a levelled road.

  1. Gravity acts vertically down; the displacement is horizontal (90°): W = Fs cos 90° = 0.
AnswerZero

(ii)(b) A person climbs a ladder.

  1. The displacement is upward, opposite to gravity (180°): W = Fs cos 180° < 0.
AnswerNegative

(ii)(c) A car in a neutral gear is coming down the slope.

  1. The car moves downhill: its displacement has a component along gravity (angle less than 90°), so gravity does positive work (it is what speeds the car up).
AnswerPositive

(iii)(a) A, B, C and D are four points on a hemispherical cup placed inverted on the ground: A is the top, B and C the ends of the diameter BC = 360 cm on the ground, and D is a point on the surface at the level of E, where E is on the vertical radius below A with AE = R/3 (R is the radius of the cup). A small spherical mass 500 g at rest at the point A slides down along the smooth surface of the cup. Assuming no loss of energy (g = 10 m s⁻²), calculate its potential energy at A relative to B.

  1. R = 360/2 = 180 cm = 1.8 m; A is R above the ground level of B: h = 1.8 m.
  2. PE=mgh=0.5×10×1.8=9PE = mgh = 0.5 \times 10 \times 1.8 = 9 J.
Answer9 J

(iii)(b) Calculate its speed at the point B (lowest point).

  1. Energy conservation: PE at A = KE at B, mgh=12mv2mgh = \dfrac{1}{2}mv^2.
  2. v=2gh=2×10×1.8=36=6 m s−1v = \sqrt{2gh} = \sqrt{2 \times 10 \times 1.8} = \sqrt{36} = 6\ \text{m s}^{-1}.
Answer6 m/s

(iii)(c) Calculate its kinetic energy at D.

  1. Height of D above B =R−R3=2R3=1.2= R - \dfrac{R}{3} = \dfrac{2R}{3} = 1.2 m; PE at D =0.5×10×1.2=6= 0.5 \times 10 \times 1.2 = 6 J.
  2. KE at D = total energy − PE at D = 9 − 6 = 3 J.
Answer3 J
Ask about this question
Q7

Question 7 (10 marks)

Machines, echoes and resonance
Question 7: (i) block and tackle with velocity ratio 4, (ii) echo from a cliff, (iii) pushing a swing.
  1. (i)(a)
    A block and tackle system of pulleys has velocity ratio 4. Draw a labelled diagram of the system indicating clearly the direction of the load and effort.
  2. (i)(b)
    Calculate the potential energy gained by a load of 100 kgf lifted by this pulley to a height of 5 m. (g = 10 m s⁻²)
  3. (ii)(a)
    A person standing in front of a cliff fires a gun and hears its echo after 3 s. Speed of sound in air is 336 m s⁻¹. Calculate the distance of the person from the cliff.
  4. (ii)(b)
    After moving a certain distance from the cliff, he fires the gun again and this time the echo is heard 1.5 s later than the first. Calculate the distance that the person has moved.
  5. (iii)(a)
    A mother pushes her daughter sitting on a swing. The swing goes through positions A, B, C, where A and C are the extreme positions (A on the mother's side) and B is the mean position. Which is the right position, A, B or C, for the mother to give a constant periodic push to the swing, every time in the forward direction, to increase the amplitude of the swing?
  6. (iii)(b)
    Name the phenomenon involved in this.
  7. (iii)(c)
    On the basis of this example, explain how this phenomenon helps to increase the amplitude of the swing.

Tests: Block and tackle, potential energy, echoes and resonance.

Show solution

(i)(a) A block and tackle system of pulleys has velocity ratio 4. Draw a labelled diagram of the system indicating clearly the direction of the load and effort.

  1. Upper block: two pulleys on one axle (or one above the other), fixed to a rigid support. Lower block: two pulleys, movable, with the load L hung from its hook.
  2. One continuous string: tied to the hook of the upper block, passing alternately round the lower and upper pulleys, so four segments of string support the lower block; the free end comes off the last upper pulley.
  3. Mark the tension T in each of the four segments (upward on the lower block), the load L acting vertically down, and the effort E applied downward at the free end.
  4. V.R. = number of string segments supporting the lower block = 4.
AnswerDiagram: 2 fixed + 2 movable pulleys, one string, 4 segments with tension T supporting the load L (down); effort E downward at the free end.

(i)(b) Calculate the potential energy gained by a load of 100 kgf lifted by this pulley to a height of 5 m. (g = 10 m s⁻²)

  1. A load of 100 kgf is the weight of a 100 kg mass.
  2. U=mgh=100×10×5=5000U = mgh = 100 \times 10 \times 5 = 5000 J.
Answer5000 J

(ii)(a) A person standing in front of a cliff fires a gun and hears its echo after 3 s. Speed of sound in air is 336 m s⁻¹. Calculate the distance of the person from the cliff.

  1. The sound goes to the cliff and back: 2d=vt2d = vt, so d=vt2d = \dfrac{vt}{2}.
  2. d=336×32=504d = \dfrac{336 \times 3}{2} = 504 m.
Answer504 m

(ii)(b) After moving a certain distance from the cliff, he fires the gun again and this time the echo is heard 1.5 s later than the first. Calculate the distance that the person has moved.

  1. Moving away from the cliff, the echo now takes 3 + 1.5 = 4.5 s.
  2. New distance d′=336×4.52=756d' = \dfrac{336 \times 4.5}{2} = 756 m.
  3. Distance moved = 756 − 504 = 252 m (away from the cliff).

    Why: The extra 1.5 s is the time for the extra distance there and back: 336 × 1.5 / 2 = 252 m. The scheme reads the 1.5 s as the second echo time and gets 504 − 252 = 252 m; same answer.

Answer252 m

(iii)(a) A mother pushes her daughter sitting on a swing. The swing goes through positions A, B, C, where A and C are the extreme positions (A on the mother's side) and B is the mean position. Which is the right position, A, B or C, for the mother to give a constant periodic push to the swing, every time in the forward direction, to increase the amplitude of the swing?

  1. Push at the extreme position next to her, where the swing is momentarily at rest and about to move forward: each push then adds energy in step with the motion.
AnswerAt A

(iii)(b) Name the phenomenon involved in this.

  1. A periodic force applied at the natural frequency of the body gives large amplitude: resonance.
AnswerResonance

(iii)(c) On the basis of this example, explain how this phenomenon helps to increase the amplitude of the swing.

  1. The mother pushes once every oscillation, so the frequency of her push equals the natural frequency of the swing.
  2. Each push is in the direction of motion and in phase with it, so energy is added every cycle; the energy builds up and the amplitude increases.
AnswerThe pushes come at the swing's natural frequency and in phase with it, so energy is added every cycle and the amplitude grows (resonance).
Ask about this question
Q8

Question 8 (10 marks)

Current electricity and household circuits
Question 8: (i) a mercury-filled tube as a resistor, (ii) the safest circuit for a 2 kW appliance, (iii) two nichrome wires.
  1. (i)(a)
    A circuit for studying Ohm's law: a battery, an ammeter and a glass tube filled with mercury (tube 1) in series, with a voltmeter across the tube's electrodes E1 and E2. The student repeats the experiment with tube 2, which the same amount of mercury fills; tube 2 is shorter and wider than tube 1. Neglecting internal resistance of the cell, use (> or < or =) to compare the resistance in both cases.
  2. (i)(b)
    Compare the voltmeter readings in both cases.
  3. (i)(c)
    Compare the specific resistance in both cases.
  4. (ii)(a)
    An appliance with a metal covering, rated at 2 kW, 220 V, is to be connected in a circuit. Four configurations: P has an 8 A fuse in the live wire and no earth connection; Q has an 8 A fuse and its metal body earthed; R has a 10 A fuse, but its earth wire goes to the element's return end, not to the metal body; S has a 10 A fuse in the live wire, a neutral wire, and its metal body earthed. Identify the safest circuit.
  5. (ii)(b)
    Write two reasons, supported by mathematical calculations, where applicable, to justify your choice.
  6. (iii)(a)
    A nichrome wire X with length l and cross-sectional area A is connected to a 10 V source, and another nichrome wire Y with length 2l and cross-sectional area A/2 is connected to a 20 V source. Compare the resistances of wires X and Y. [Given that the resistivity of nichrome is ρ.]
  7. (iii)(b)
    Compare the electrical power consumed by each wire.
  8. (iii)(c)
    Compare the masses of these wires. (Given that the density of nichrome is d.)
  9. (iii)(d)
    State True or False: Wire X and wire Y both show the same rise in temperature in the same time.

Tests: Resistance and resistivity, fuse rating and earthing, power and heating in wires.

Show solution

(i)(a) A circuit for studying Ohm's law: a battery, an ammeter and a glass tube filled with mercury (tube 1) in series, with a voltmeter across the tube's electrodes E1 and E2. The student repeats the experiment with tube 2, which the same amount of mercury fills; tube 2 is shorter and wider than tube 1. Neglecting internal resistance of the cell, use (> or < or =) to compare the resistance in both cases.

  1. R=ρlAR = \rho\dfrac{l}{A}. The same volume of mercury in tube 2 forms a shorter, thicker column: ll smaller, AA larger.
  2. Both changes lower the resistance.
AnswerRtube 2<Rtube 1R_{\text{tube 2}} < R_{\text{tube 1}}

(i)(b) Compare the voltmeter readings in both cases.

  1. With no internal resistance (and an ideal ammeter), the whole battery voltage appears across the tube in both cases: the voltmeter reading is the same, V1 = V2 (only the current changes).
AnswerV1=V2V_1 = V_2

(i)(c) Compare the specific resistance in both cases.

  1. Specific resistance (resistivity) depends only on the material and temperature; both tubes hold mercury, so it is the same: ρ1 = ρ2.
Answerρ1=ρ2\rho_1 = \rho_2

(ii)(a) An appliance with a metal covering, rated at 2 kW, 220 V, is to be connected in a circuit. Four configurations: P has an 8 A fuse in the live wire and no earth connection; Q has an 8 A fuse and its metal body earthed; R has a 10 A fuse, but its earth wire goes to the element's return end, not to the metal body; S has a 10 A fuse in the live wire, a neutral wire, and its metal body earthed. Identify the safest circuit.

  1. The safest circuit needs a fuse rated just above the working current and the metal body earthed. Only S has both.
AnswerS

(ii)(b) Write two reasons, supported by mathematical calculations, where applicable, to justify your choice.

  1. 1. Working current I=PV=2000220=9.09I = \dfrac{P}{V} = \dfrac{2000}{220} = 9.09 A. An 8 A fuse (P, Q) would blow in normal use; a 10 A fuse (R, S) carries 9.09 A but melts on a larger fault current.
  2. 2. The metal body is earthed in S: if the live wire touches the body, the current flows to earth (and blows the fuse) instead of through the person. In R the metal body is not earthed.
AnswerI = 2000/220 = 9.09 A, so a 10 A fuse is right; and S's metal body is earthed.

(iii)(a) A nichrome wire X with length l and cross-sectional area A is connected to a 10 V source, and another nichrome wire Y with length 2l and cross-sectional area A/2 is connected to a 20 V source. Compare the resistances of wires X and Y. [Given that the resistivity of nichrome is ρ.]

  1. RX=ρlAR_X = \dfrac{\rho l}{A}; RY=ρ(2l)A/2=4ρlA=4RXR_Y = \dfrac{\rho (2l)}{A/2} = \dfrac{4\rho l}{A} = 4R_X.
  2. RX:RY=1:4R_X : R_Y = 1 : 4.
AnswerRX:RY=1:4R_X : R_Y = 1 : 4

(iii)(b) Compare the electrical power consumed by each wire.

  1. P=V2RP = \dfrac{V^2}{R}: PX=102RX=100RXP_X = \dfrac{10^2}{R_X} = \dfrac{100}{R_X}; PY=2024RX=100RXP_Y = \dfrac{20^2}{4R_X} = \dfrac{100}{R_X}.
  2. PX:PY=1:1P_X : P_Y = 1 : 1.
AnswerPX:PY=1:1P_X : P_Y = 1 : 1

(iii)(c) Compare the masses of these wires. (Given that the density of nichrome is d.)

  1. Mass = volume × density: mX=A l dm_X = A\,l\,d; mY=A2×2l×d=A l dm_Y = \dfrac{A}{2} \times 2l \times d = A\,l\,d.
  2. mX:mY=1:1m_X : m_Y = 1 : 1.
AnswermX:mY=1:1m_X : m_Y = 1 : 1

(iii)(d) State True or False: Wire X and wire Y both show the same rise in temperature in the same time.

  1. Heat produced in time tt: Q=PtQ = Pt, the same for both since PX=PYP_X = P_Y.
  2. Q=mcΔTQ = mc\Delta T with the same mm (part c) and the same cc (both nichrome), so ΔT\Delta T is the same.
AnswerTrue
Ask about this question
Q9

Question 9 (10 marks)

Electricity, electromagnetic induction and radioactivity
Question 9: (i) three bulbs, (ii) output of an AC generator, (iii) neutron-proton graph for elements A to E.
  1. (i)(a)
    Three bulbs of powers P1, P2 and P3 (P1 < P2 < P3) are connected in a certain way that P3 glows brightest. What type of connection exists between these bulbs?
  2. (i)(b)
    Compare the voltage across these bulbs. (Use >, < or =)
  3. (i)(c)
    Will the circuit still function if one of the bulbs is fused?
  4. (ii)(a)
    A graph of induced e.m.f. against time for an AC generator: a sine wave starting at the origin; 'a' marks the peak e.m.f. (height of a crest above the time axis) and 'b' the time from 0 to the end of one complete cycle. If the speed of the generator coil is doubled, what is the effect on the physical quantity indicated by 'a'?
  5. (ii)(b)
    What is the effect on the physical quantity indicated as 'b'?
  6. (ii)(c)
    Give reason for your answer in (b).
  7. (iii)(a)
    Fig. A plots number of neutrons (y-axis) against number of protons (x-axis): A (88, 144), B (90, 144), C (92, 146), D (93, 146), E (93, 145). Identify the radioactive radiation emitted when element C decays into element E. Represent this using a nuclear reaction.
  8. (iii)(b)
    What is the special name given to elements D and E?
  9. (iii)(c)
    If element C transforms into element B by emitting a radioactive ray, how will this ray behave in an electric field?

Tests: Parallel circuits, AC generator output, and reading alpha and beta decays from an N-Z plot.

Show solution

(i)(a) Three bulbs of powers P1, P2 and P3 (P1 < P2 < P3) are connected in a certain way that P3 glows brightest. What type of connection exists between these bulbs?

  1. Higher rated power means lower resistance (R=V2/PR = V^2/P), so R3R_3 is the smallest.
  2. In parallel each bulb gets the full voltage and P=V2/RP = V^2/R is largest for the smallest RR: P3 glows brightest. (In series, P=I2RP = I^2R would make P1 brightest.)
AnswerParallel

(i)(b) Compare the voltage across these bulbs. (Use >, < or =)

  1. In parallel the same voltage acts across every branch.
AnswerV1=V2=V3V_1 = V_2 = V_3

(i)(c) Will the circuit still function if one of the bulbs is fused?

  1. Each bulb has its own path to the supply; a fused bulb breaks only its own branch, so the other two stay lit.
AnswerYes

(ii)(a) A graph of induced e.m.f. against time for an AC generator: a sine wave starting at the origin; 'a' marks the peak e.m.f. (height of a crest above the time axis) and 'b' the time from 0 to the end of one complete cycle. If the speed of the generator coil is doubled, what is the effect on the physical quantity indicated by 'a'?

  1. 'a' is the peak e.m.f. e0=NBAωe_0 = NBA\omega.
  2. Doubling the speed doubles ω\omega, so the peak e.m.f. is doubled.

    Why: The flux changes twice as fast.

Answer'a' (peak e.m.f.) is doubled.

(ii)(b) What is the effect on the physical quantity indicated as 'b'?

  1. 'b' is the time period T=1fT = \dfrac{1}{f}. Doubling the speed doubles ff, so TT is halved.
Answer'b' (time period) is halved.

(ii)(c) Give reason for your answer in (b).

  1. One cycle of e.m.f. is produced per rotation of the coil. At double the speed each rotation takes half the time, so the time of one cycle (the period) is halved.
AnswerAt double speed the coil completes each rotation, i.e. each cycle, in half the time.

(iii)(a) Fig. A plots number of neutrons (y-axis) against number of protons (x-axis): A (88, 144), B (90, 144), C (92, 146), D (93, 146), E (93, 145). Identify the radioactive radiation emitted when element C decays into element E. Represent this using a nuclear reaction.

  1. C: Z = 92, N = 146, A = 238. E: Z = 93, N = 145, A = 238.
  2. One neutron has become a proton (Z up by 1, A unchanged): a beta particle (electron) is emitted.
  3. 92238C→93238E+−10β^{238}_{92}\text{C} \to {}^{238}_{93}\text{E} + {}^{0}_{-1}\beta
AnswerBeta (β\beta) radiation: 92238C→93238E+−10β^{238}_{92}\text{C} \to {}^{238}_{93}\text{E} + {}^{0}_{-1}\beta

(iii)(b) What is the special name given to elements D and E?

  1. D and E have the same number of protons (93) but different numbers of neutrons (146 and 145): mass numbers 239 and 238.
AnswerIsotopes

(iii)(c) If element C transforms into element B by emitting a radioactive ray, how will this ray behave in an electric field?

  1. C (92, 146) to B (90, 144): 2 protons and 2 neutrons lost, so an alpha particle is emitted.
  2. An alpha particle is positively charged, so in an electric field it is deflected towards the negative plate (only slightly, being heavy).
AnswerIt is an alpha particle (positive), deflected towards the negative plate.
Ask about this question

Questions are quoted from the ICSE 2026 Physics Specimen Question Paper (521); figures are described in words. Every final answer is checked against the official CISCE answers. Where a question offers a choice, every option is solved.

CISCE specimen question papers and their answers are referenced for educational and review purposes only, under fair dealing. All copyrights in the questions belong to the Council for the Indian School Certificate Examinations. Solutions and explanations provided here are original works by Your Abhyaasika, generated with AI, and may contain mistakes. Your Abhyaasika is not affiliated with CISCE.