ISC Class 12 Physics Specimen Paper 2026 with Solutions
Step-by-step solutions to every question of the ISC 2026 Specimen Question Paper for Physics Paper 1 (Theory), Class 12: the fourteen one-mark items of Section A, the two-mark questions of Section B, the three-mark questions of Section C and the five-mark questions of Section D, with both alternatives solved wherever the paper offers a choice. Each solution follows the ISC marking style (formula, substitution, result with units) and every answer is checked against the official CISCE Specimen Answer Key; where the key slips, the solution follows the physics and says so.
ISC 2026 Physics Specimen Question Paper (861A): 27 questions, 70 marks, 3 hours. Open any question to see the steps one at a time or ask a doubt about a step. Also solved: Physics Specimen Paper 2025.
Section A: 14 marks: one question having fourteen sub-parts of one mark each; answer all
Question 1 (i) (1 mark)
Electric flux and Gauss's lawTests: Total flux through a closed surface depends only on the net charge inside it.
Show solution
- Gauss's law: , whatever the size of the surface.
- Charge enclosed , so .
Why: The two charges form a dipole: as many field lines enter the sphere as leave it.
Question 1 (ii) (1 mark)
Force between parallel currentsTests: Parallel currents attract, antiparallel currents repel, with force proportional to I₁I₂/d.
Show solution
- Force per unit length between two long parallel wires: ; like currents attract, unlike currents repel.
- Wire 1 (out of the page, distance ) attracts wire 3 towards itself: .
- Wire 2 is on the same side of wire 3 as wire 1, so to cancel this pull it must push wire 3 away: its current is opposite to I₃, that is into the page.
Why: An attraction from wire 2 would add to the pull of wire 1.
- Equal magnitudes: , so .
- The specimen answer key gives (c) (2I₁ out of the page). With the distances as drawn, that would double the attraction instead of cancelling it; the physics gives (b).
Question 1 (iii) (1 mark)
Magnetic properties of materialsTests: Temperature dependence of susceptibility for dia-, para- and ferromagnetic substances.
Show solution
- Diamagnetism comes from the orbital motion of electrons responding to the applied field; thermal agitation does not affect it, so χ is independent of temperature.
- (b) is Curie's law for a paramagnetic; (c) is a ferromagnetic above its Curie temperature, ; nothing behaves like (d).
- So the graph is a horizontal line: (a). Strictly, χ of a diamagnetic is small and negative, so the line lies just below the T-axis; the printed graph draws it above the axis, but it is the only temperature-independent option.
Question 1 (iv) (1 mark)
Dual nature of matterTests: de Broglie wavelength of a particle versus the wavelength of a photon of equal energy.
Show solution
- Electron of kinetic energy E: , so and .
- Photon of energy E: .
- Both are proportional to , so .
Question 1 (v) (1 mark)
Semiconductor diodesTests: Forward bias: the p side at a higher potential than the n side.
Show solution
- A diode is forward biased when its p side (the triangle) is at a higher potential than its n side (the bar).
- (R): p side at −5 V, n side at −12 V. −5 V is higher than −12 V, so (R) is forward biased.
Why: Compare potentials, not sizes: −5 V is above −12 V.
- (S): p side earthed (0 V), n side at +5 V through R: reverse biased.
- As drawn, (P) (p side at +10 V, n side at +5 V) and (Q) (p side at 10 V through R, n side earthed) are forward biased too, so no option lists exactly the forward-biased diodes (P), (Q) and (R). The specimen answer key gives (b) Only (R); the page keeps the board's key and flags the item.
Question 1 (vi) (1 mark)
Refraction through a prismTests: Deviation and dispersion by a prism.
Show solution
- Every colour is bent towards the base on refraction at the two faces, so the light is deviated.
- The refractive index of glass depends on wavelength (), so each colour is deviated by a different angle and white light spreads into a spectrum: dispersion.
Question 1 (vii) (1 mark)
Reflection by spherical mirrorsTests: Focal length of a mirror is fixed by its radius of curvature, not by the medium.
Show solution
- For any spherical mirror : it depends only on the curvature. The Reason is true.
- The law of reflection does not involve the refractive index of the surrounding medium, so the focal length of a mirror is the same in water as in air. The Assertion is false.
Question 1 (7 marks)
Short answers across the syllabus- (i)Current I flowing through a metallic wire is gradually increased. Show graphically how heating power (P) developed in it varies with the current (I).
- (ii)State one method to minimise flux loss in a transformer.
- (iii)Why are giant telescopes of reflecting type? Give any one scientific reason.
- (iv)Give any one example where a ray of light travelling from one optical medium to another travels undeviated.
- (v)Two charged particles having same charge but different masses, are passed through a potential difference V. When V is varied, de-Broglie wavelength (λ) of the particles varies as shown in graphs below. Which graph is for heavier particles and why? (Graph: λ on the y-axis against 1/√V on the x-axis; two straight lines through the origin, B steeper than A.)
- (vi)What happens when an electron collides with a positron?
- (vii)What is the direction of flow of electrons in a solar cell?
Tests: One-mark recall and reasoning across current electricity, AC, optics, modern physics and semiconductors.
Show solution
(i) Current I flowing through a metallic wire is gradually increased. Show graphically how heating power (P) developed in it varies with the current (I).
- Joule heating: . For a fixed resistance, .
- Graph: P on the y-axis, I on the x-axis; a parabola starting at the origin, flat near I = 0 and curving upwards ever more steeply.
Why: Doubling the current makes the heating four times as large.
- As the wire warms, its resistance rises a little, so the real curve bends up slightly faster than a pure parabola.
(ii) State one method to minimise flux loss in a transformer.
- Wind the primary and secondary coils close together, one over the other (interleaved) on the same limb, so that almost all the flux of one links the other.
- Use a closed core of high permeability (soft iron), which keeps the flux inside the core.
(iii) Why are giant telescopes of reflecting type? Give any one scientific reason.
- A mirror reflects all colours alike, so a reflecting telescope's image has no chromatic aberration.
- Other acceptable reasons: a paraboloidal mirror is free from spherical aberration; a large mirror is lighter, easier to support from behind and cheaper than a large lens; a bigger aperture collects more light, giving a brighter image.
(iv) Give any one example where a ray of light travelling from one optical medium to another travels undeviated.
- Snell's law: . If then .
- So a ray falling normally on the boundary (along the normal) goes straight through. A ray also passes undeviated when the two media have the same refractive index.
(v) Two charged particles having same charge but different masses, are passed through a potential difference V. When V is varied, de-Broglie wavelength (λ) of the particles varies as shown in graphs below. Which graph is for heavier particles and why? (Graph: λ on the y-axis against 1/√V on the x-axis; two straight lines through the origin, B steeper than A.)
- Kinetic energy gained: , so and .
- So against is a straight line through the origin with slope .
- Same q: the slope is proportional to . The heavier particle has the smaller slope, which is line A.
- The specimen answer key says B, reading the slope the wrong way round: the steeper line B is the lighter particle.
(vi) What happens when an electron collides with a positron?
- They annihilate each other: their mass is converted into energy, emitted as gamma-ray photons (usually two, each of about 0.51 MeV when the pair is at rest), conserving charge, energy and momentum.
(vii) What is the direction of flow of electrons in a solar cell?
- Light absorbed near the junction creates electron-hole pairs. The junction's built-in field sweeps the electrons to the n side and the holes to the p side.
- In the external circuit, electrons flow from the n side through the load to the p side (conventional current flows from p to n through the load).
Section B: 14 marks: seven questions of two marks each; internal choice in two questions
Question 2 (2 marks)
Capacitors and resistance- (i)(a)Find the capacitance of the following combination between terminals A and B. Area of each plate is A and separation between nearest two plates is d. (Figure 2: four parallel plates, numbered 1 to 4 from the top; terminal A is joined to plates 1 and 4, terminal B to plates 2 and 3.)
- (i)(b)Figure 3: four parallel plates numbered 1 to 4 from the top; terminal A is joined to plates 1 and 3, terminal B to plates 2 and 4.
- (ii)(a)OR: The current (I)-voltage (V) graphs for a conductor are given at two different temperatures T₁ and T₂ (two straight lines through the origin, I on the y-axis and V on the x-axis; the T₁ line makes the larger angle θ₁ with the V-axis, the T₂ line the smaller angle θ₂). At which temperature T₁ or T₂ is the resistance higher?
- (ii)(b)Which temperature T₁ or T₂ is higher?
Tests: Spot capacitors in parallel in a plate arrangement; read resistance from the slope of an I-V graph.
Show solution
(i)(a) Find the capacitance of the following combination between terminals A and B. Area of each plate is A and separation between nearest two plates is d. (Figure 2: four parallel plates, numbered 1 to 4 from the top; terminal A is joined to plates 1 and 4, terminal B to plates 2 and 3.)
- Plates 1 and 2 face each other with A on one and B on the other: one capacitor C. Plates 3 and 4: another capacitor C.
- Plates 2 and 3 are both joined to B, so they are at the same potential and store no charge between them.
- Both capacitors sit between A and B: they are in parallel, , with .
(i)(b) Figure 3: four parallel plates numbered 1 to 4 from the top; terminal A is joined to plates 1 and 3, terminal B to plates 2 and 4.
- Each neighbouring pair (1-2, 2-3, 3-4) has A on one plate and B on the other, so each pair is a capacitor C between A and B.
- Three capacitors in parallel: .
Why: The inner plates 2 and 3 are charged on both faces.
(ii)(a) OR: The current (I)-voltage (V) graphs for a conductor are given at two different temperatures T₁ and T₂ (two straight lines through the origin, I on the y-axis and V on the x-axis; the T₁ line makes the larger angle θ₁ with the V-axis, the T₂ line the smaller angle θ₂). At which temperature T₁ or T₂ is the resistance higher?
- The slope of an I-V graph is the conductance: , so .
- , so and .
(ii)(b) Which temperature T₁ or T₂ is higher?
- The resistance of a metallic conductor rises with temperature (more frequent collisions of electrons with the vibrating ions).
- The resistance is higher at T₂, so T₂ is the higher temperature.
Question 3 (2 marks)
Electric dipoleTests: Add dipole moments as vectors.
Show solution
- Each O-H pair is a dipole of charges separated by : , directed from the oxygen towards the hydrogen.
- The two dipole moments make an angle : .
- With : , along the bisector of the angle, pointing from O towards the H side.
Why: Equivalently, each moment's component along the bisector is el cos(θ/2); the perpendicular components cancel.
Question 4 (2 marks)
Current electricity: cells and the metre bridge- (i)Two cells of same emf E, but different internal resistance r₁ and r₂ are connected to an external resistance R as shown in Figure 5 (the two cells in series, aiding each other, in a single loop with R; the voltmeter is connected across the first cell, that is across E and r₁). The voltmeter V reads zero. Obtain an expression for R in terms of r₁ and r₂. (Assume that the voltmeter V is of infinite resistance.)
- (ii)(a)OR: Ramesh performed an experiment to determine an unknown resistance R using the circuit shown in Figure 6 (a metre bridge: resistance box X and the coiled resistor R in the top gap, X on the P side; PQ is a 100 cm wire with a cell and key across it; a galvanometer from the junction of X and R to a jockey J at distance l from P). He closed the key and inserted X = 1 Ω, 2 Ω ... and recorded the null point (l) for each. Identify the principle involved in calculating R.
- (ii)(b)Write down a relation required to calculate the resistance R in terms of X and (l).
Tests: Terminal voltage of a cell; the balance condition of a metre bridge.
Show solution
(i) Two cells of same emf E, but different internal resistance r₁ and r₂ are connected to an external resistance R as shown in Figure 5 (the two cells in series, aiding each other, in a single loop with R; the voltmeter is connected across the first cell, that is across E and r₁). The voltmeter V reads zero. Obtain an expression for R in terms of r₁ and r₂. (Assume that the voltmeter V is of infinite resistance.)
- Total emf , total resistance : .
- Terminal voltage of the first cell: , so .
- .
- This needs : the voltmeter must be across the cell with the larger internal resistance.
(ii)(a) OR: Ramesh performed an experiment to determine an unknown resistance R using the circuit shown in Figure 6 (a metre bridge: resistance box X and the coiled resistor R in the top gap, X on the P side; PQ is a 100 cm wire with a cell and key across it; a galvanometer from the junction of X and R to a jockey J at distance l from P). He closed the key and inserted X = 1 Ω, 2 Ω ... and recorded the null point (l) for each. Identify the principle involved in calculating R.
- The metre bridge is a Wheatstone bridge: X, R and the two parts of the wire (lengths l and 100 − l) are its four arms.
- At the null point no current flows through the galvanometer, and the ratio of the arms is equal: P/Q = R/S.
(ii)(b) Write down a relation required to calculate the resistance R in terms of X and (l).
- The wire is uniform, so the resistances of its two parts are in the ratio of their lengths: .
- (l in cm).
Question 5 (2 marks)
Moving coil galvanometerTests: Voltage sensitivity of a galvanometer depends on N/R.
Show solution
- Voltage sensitivity: deflection per unit voltage, (k is the torsion constant).
- : .
- : .
- B, A and k are the same for both, so G₂ is four times as sensitive to voltage.
Question 6 (2 marks)
Refraction through lenses- (i)Figure 7: the lens is cut by a plane parallel to the principal axis; the small top part is of one material and the rest of another.
- (ii)Figure 8: the lens is cut by a plane perpendicular to the principal axis into two plano-convex halves of different materials, in contact.
Tests: A lens forms one image per focal length; lenses in contact act as one lens.
Show solution
(i) Figure 7: the lens is cut by a plane parallel to the principal axis; the small top part is of one material and the rest of another.
- Lens maker's formula: . Both parts have the same surfaces but different , so different focal lengths.
- Each part acts as a separate lens, bringing its light to its own focus: two images.
(ii) Figure 8: the lens is cut by a plane perpendicular to the principal axis into two plano-convex halves of different materials, in contact.
- Every ray passes through both halves. The two plano-convex lenses in contact act as one lens of power P = P₁ + P₂.
- One focal length, so one image.
Question 7 (2 marks)
Electromagnetic waves- (a)radars
- (b)crystallography
Tests: Uses of the parts of the electromagnetic spectrum.
Show solution
(a) radars
- Radar uses microwaves (wavelengths of about 1 mm to 30 cm): they travel in narrow beams and reflect well from aircraft and ships.
(b) crystallography
- Crystallography uses X-rays: their wavelength (about 0.1 nm) is comparable to the spacing of atoms in a crystal, so the crystal diffracts them.
Question 8 (2 marks)
Photoelectric effectTests: Einstein's photoelectric equation: the maximum KE rises linearly with frequency.
Show solution
- Einstein's equation: , so .
- New frequency : .
- Change: .
Section C: 27 marks: nine questions of three marks each; internal choice in two questions
Question 9 (3 marks)
Electrostatic potentialTests: Potential of a point charge as work done per unit charge from infinity.
Show solution
- Potential at P is the work done in bringing a unit positive charge from infinity to P (at distance r from Q, placed at O), without acceleration.
- When the unit charge is at distance x from Q, the repulsive force on it is , directed away from Q.
- Work done against this force in a small displacement towards Q: .
- .
- .
Question 10 (3 marks)
Coulomb's law and Kirchhoff's laws- (i)Five identical charges are placed equidistant on a semicircle as shown in Figure 9 (the left half of a circle of radius 2 cm: one charge at the top, one at the bottom, one at the far left on the horizontal diameter and one midway on each arc, at 45° above and below it). Another point charge is kept at the centre of the circle. Calculate the electrostatic force experienced by the charge q.
- (ii)OR: Using Kirchhoff's laws of electrical networks, calculate the current I₃. (Figure 10: three vertical branches between the top line ABC and the bottom line FED. Left branch FA: a 33 V cell of internal resistance 1 Ω (positive terminal up) and 2 Ω, carrying I₁ up to A, then A to B. Middle branch EB: a 24 V cell of internal resistance 2 Ω (positive terminal up) and 6 Ω, carrying I₂ up to B. Right branch CD: 8 Ω, carrying I₃ from B through C down to D.)
Tests: Vector addition of Coulomb forces using symmetry; Kirchhoff's junction and loop rules.
Show solution
(i) Five identical charges are placed equidistant on a semicircle as shown in Figure 9 (the left half of a circle of radius 2 cm: one charge at the top, one at the bottom, one at the far left on the horizontal diameter and one midway on each arc, at 45° above and below it). Another point charge is kept at the centre of the circle. Calculate the electrostatic force experienced by the charge q.
- Each charge exerts a force of the same size on q: , repulsive.
- The top and bottom charges push q in opposite directions: their forces cancel.
- The two 45° charges: vertical components cancel; horizontal components add, , away from the semicircle.
- The far-left charge adds in the same direction. Net force: .
(ii) OR: Using Kirchhoff's laws of electrical networks, calculate the current I₃. (Figure 10: three vertical branches between the top line ABC and the bottom line FED. Left branch FA: a 33 V cell of internal resistance 1 Ω (positive terminal up) and 2 Ω, carrying I₁ up to A, then A to B. Middle branch EB: a 24 V cell of internal resistance 2 Ω (positive terminal up) and 6 Ω, carrying I₂ up to B. Right branch CD: 8 Ω, carrying I₃ from B through C down to D.)
- Junction rule at B: .
- Loop rule, loop ABCDEFA: , so .
- Loop BCDEB: , so , that is .
- From the second, ; then , .
- .
Why: Check: the 8 Ω resistor then has 24 V across it, exactly the 24 V cell's emf, so the middle branch carries no current.
Question 11 (3 marks)
Ampere's circuital lawTests: Use symmetry and Ampere's law to find the field of a long straight wire.
Show solution
- Ampere's circuital law: , where I is the current threaded by the closed loop.
- Take as the Amperian loop a circle of radius r centred on the wire, in a plane perpendicular to it. By symmetry B has the same magnitude at every point of the circle and is along the tangent, parallel to dl (θ = 0).
- .
- .
Question 12 (3 marks)
Magnetic field of a coil; motion in a magnetic field- (i)A student records the following data for the magnitudes (B) of the magnetic field at axial points at different distances x (Figure 11: a circular coil of radius a with centre O; P is on its axis at distance x from O) from the centre O of a circular coil of radius a carrying a current I. Verify (for any two) that these observations are in good agreement with the expected theoretical values of B.
x x = 0 x = a x = 2a x = 3a B - (ii)(a)OR: An electron moving along positive X axis with a velocity of enters a region having uniform magnetic field along positive Y axis. Explain why the electron describes a circular path.
- (ii)(b)Calculate the radius of the circular path described by the electron.
Tests: Field on the axis of a circular coil; radius of circular motion in a magnetic field.
Show solution
(i) A student records the following data for the magnitudes (B) of the magnetic field at axial points at different distances x (Figure 11: a circular coil of radius a with centre O; P is on its axis at distance x from O) from the centre O of a circular coil of radius a carrying a current I. Verify (for any two) that these observations are in good agreement with the expected theoretical values of B.
- Field on the axis: ; at the centre () . So .
- : . Agrees.
- : . Agrees.
- : . Agrees.
(ii)(a) OR: An electron moving along positive X axis with a velocity of enters a region having uniform magnetic field along positive Y axis. Explain why the electron describes a circular path.
- The magnetic force is always perpendicular to the velocity, so it does no work: the speed stays constant.
- A force of constant size always at right angles to the velocity acts as a centripetal force, so the path is a circle. Here v is perpendicular to B, so there is no velocity component along B and the path is a circle, not a helix.
- At entry is along ; the electron's charge is negative, so the force is along : the circle lies in the XZ plane.
(ii)(b) Calculate the radius of the circular path described by the electron.
- .
- .
Question 13 (3 marks)
Wave optics: Huygens' principle- (i)A primary wavefront
- (ii)A secondary wavefront
- (iii)A wave normal
Tests: Huygens' construction: wavelets, envelope and wave normals.
Show solution
(i) A primary wavefront
- The wavefront from which the construction starts, centred on the source S, is the arc through A, B, C, D.
(ii) A secondary wavefront
- After time t each point of ABCD has sent out a secondary wavelet of radius ct; the forward envelope (common tangent) of these wavelets is the new wavefront A′B′C′D′.
(iii) A wave normal
- A wave normal is perpendicular to the wavefronts, along the direction of propagation: for a point source, a radius such as SAA′.
Question 14 (3 marks)
Wave optics: Young's double slitTests: Path difference in Young's experiment and the positions of bright and dark fringes.
Show solution
- Slits A and B are a distance apart; the screen is at distance (). For a point P at height from the centre O of the screen, the path difference is , where AN is drawn perpendicular to BP.
- is small, so , and the path difference is .
- Bright fringe of order m: .
- Fringe width: . (The dark fringes, at path difference , give the same spacing.)
Question 15 (3 marks)
Refraction at spherical surfaces; lens maker's formula- (i)(a)Apply the formula (expression) of refraction at a single spherical surface to refraction at first spherical surface.
- (i)(b)Refraction at second spherical surface.
- (ii)Combine these two expressions / equations to obtain an expression for focal length of the lens.
Tests: Derive the lens maker's formula from refraction at two spherical surfaces.
Show solution
(i)(a) Apply the formula (expression) of refraction at a single spherical surface to refraction at first spherical surface.
- Refraction at a spherical surface: .
- First surface (from into , radius ; object O at distance u; image I₁ at ): .
(i)(b) Refraction at second spherical surface.
- I₁ acts as the object for the second surface (the lens is thin, so its distance is still ); light goes from back into across a surface of radius , forming the final image I at v.
- .
(ii) Combine these two expressions / equations to obtain an expression for focal length of the lens.
- Add the two equations; the terms cancel: .
- For an object at infinity () the image is at the focus, : .
- For a lens of refractive index in air: . For this biconvex lens is negative, so in magnitudes , the form in the answer key.
Question 16 (3 marks)
Optical instruments- (i)A student studies details of a microorganism with the help of an instrument. Name the instrument used by him.
- (ii)Draw a labelled ray diagram of an image formed by this instrument, assuming (a) a small upright object, (b) the image lies at least distance of distinct vision.
Tests: Image formation in a compound microscope with the final image at the near point.
Show solution
(i) A student studies details of a microorganism with the help of an instrument. Name the instrument used by him.
- A microorganism needs a large magnification, more than a single lens gives, so a two-lens instrument is used.
(ii) Draw a labelled ray diagram of an image formed by this instrument, assuming (a) a small upright object, (b) the image lies at least distance of distinct vision.
- Draw the principal axis with the objective (short focal length fₒ) on the left and the eyepiece (larger focal length fₑ) on the right.
- Place a small upright object AB just beyond Fₒ of the objective. Two rays from A (one parallel to the axis, refracted through Fₒ′; one through the optical centre, undeviated) meet at A′: a real, inverted, magnified image A′B′ beyond 2Fₒ′ on the other side.
- A′B′ lies just inside the focus Fₑ of the eyepiece. Rays from A′ (one parallel to the axis, refracted through Fₑ; one through the eyepiece centre) diverge after the eyepiece; extend them backwards (dotted) to meet at A″.
- The final image A″B″ is virtual, inverted with respect to the object, highly magnified, and at D = 25 cm from the eyepiece. Label AB, A′B′, A″B″, Fₒ, Fₑ, uₒ, vₒ, uₑ, D, 'Objective' and 'Eyepiece', with arrows on the rays.
Question 17 (3 marks)
Atoms and photoelectric effectTests: Combine Bohr energy levels with the photoelectric equation.
Show solution
- Energy levels: , so and .
- Photon energy: .
- Einstein's equation: .
- .
Section D: 15 marks: three questions of five marks each; internal choice in two questions
Question 18 (5 marks)
Self-inductance and AC circuits- (i)(a)Define the co-efficient of self-inductance.
- (i)(b)(1)Consider an A.C. source of frequency Hz applied across a coil. For each value of V-I in the tabulation, evaluate inductive reactance and self-inductance of the coil.
S.No. V (volt) I (A) 1 3.0 0.5 2 6.0 1.0 3 9.0 1.5 - (i)(b)(2)If a D.C. source be connected to the same coil, what would be the value of inductive reactance?
- (ii)(a)OR: Three students, X, Y and Z performed an experiment for studying the variation of A.C. with frequency in a series LCR circuit and obtained the graphs as shown (Figure 14: current against frequency; all three curves peak at the same resonant frequency f₀; X has the highest and sharpest peak, I₀, Y a lower and broader one, Z the lowest and broadest). They all used an AC source of the same emf and inductance of the same value. Who used minimum resistance?
- (ii)(b)In which case will the quality Q factor be maximum?
- (ii)(c)What did the students conclude about the nature of impedance at resonant frequency (f₀)?
- (ii)(d)An ideal capacitor is connected across 220 V, 50 Hz, and 220 V, 100 Hz supplies. Find the ratio of current flowing through it in the two cases.
Tests: Inductive reactance and self-inductance from V-I data; resonance, Q factor and capacitive reactance.
Show solution
(i)(a) Define the co-efficient of self-inductance.
- The flux linked with a coil is proportional to its own current: . The constant L is the coefficient of self-inductance.
- So L is the magnetic flux linked with the coil when unit current flows through it. Equivalently, from , it is the emf induced when the current changes at unit rate. SI unit: henry (H).
(i)(b)(1) Consider an A.C. source of frequency Hz applied across a coil. For each value of V-I in the tabulation, evaluate inductive reactance and self-inductance of the coil.
- Inductive reactance: : in all three rows.
- Angular frequency: .
- for every row.
(i)(b)(2) If a D.C. source be connected to the same coil, what would be the value of inductive reactance?
- For DC, , so : the coil opposes only through its resistance.
(ii)(a) OR: Three students, X, Y and Z performed an experiment for studying the variation of A.C. with frequency in a series LCR circuit and obtained the graphs as shown (Figure 14: current against frequency; all three curves peak at the same resonant frequency f₀; X has the highest and sharpest peak, I₀, Y a lower and broader one, Z the lowest and broadest). They all used an AC source of the same emf and inductance of the same value. Who used minimum resistance?
- At resonance , so the peak current is . The same E for all three: the highest peak means the smallest R.
(ii)(b) In which case will the quality Q factor be maximum?
- . The same and L for all three, so Q is largest for the smallest R.
- This is X, whose resonance curve is also the sharpest.
(ii)(c) What did the students conclude about the nature of impedance at resonant frequency (f₀)?
- At , , so .
- The impedance is minimum and purely resistive: the current is maximum and in phase with the voltage.
(ii)(d) An ideal capacitor is connected across 220 V, 50 Hz, and 220 V, 100 Hz supplies. Find the ratio of current flowing through it in the two cases.
- , so for the same V.
- .
Question 19 (5 marks)
Nuclei and atoms- (i)(a)Study the graph (binding energy per nucleon, in MeV, against mass number A, from ²H at about 1.1 MeV through ⁴He, ⁶Li, ¹²C, ¹⁴N, ¹⁶O up to a broad maximum of about 8.8 MeV near ⁵⁶Fe, then falling slowly to about 7.6 MeV at ²³⁸U; Region A covers the light nuclei up to A of about 30, Region B the middle range around the peak, from about 30 to 170, and Region C the heavy nuclei beyond about 170). Indicate which region corresponds to: (1) nuclei prone to fission, (2) nuclei prone to fusion, (3) most stable nuclei.
- (i)(b)In Rutherford's scattering experiment when an alpha particle (charge , mass ) approaches a gold nucleus (), it is continuously repelled, so it loses its kinetic energy (K) and its potential energy increases. Finally, the α-particle comes to rest momentarily when whole of the kinetic energy is changed into the potential energy of the charge at that distance from the nucleus. Let this distance be , after which the α-particle returns back again due to electrostatic repulsion. Using the above information, derive an expression for .
- (ii)(a)OR: In an atom X, electrons absorb the energy from an external source. This energy excites the electrons from a lower-energy level to a higher-energy level around the nucleus of the atom. When electrons return to the ground state, they emit photons. Figure 15 is the energy level diagram of atom X with three energy levels, E₁ = 0.00 eV, E₂ = 1.78 eV and E₃ = 2.95 eV. The ground state is considered 0 eV for reference. What wavelength of radiation is needed to excite the atom to energy level E₂ from E₁?
- (ii)(b)(1)According to Bohr's theory of hydrogen atom, calculate the angular momentum of the electron in second Bohr orbit.
- (ii)(b)(2)Radius of the third Bohr orbit.
Tests: Binding-energy curve, distance of closest approach, energy levels and Bohr's postulates.
Show solution
(i)(a) Study the graph (binding energy per nucleon, in MeV, against mass number A, from ²H at about 1.1 MeV through ⁴He, ⁶Li, ¹²C, ¹⁴N, ¹⁶O up to a broad maximum of about 8.8 MeV near ⁵⁶Fe, then falling slowly to about 7.6 MeV at ²³⁸U; Region A covers the light nuclei up to A of about 30, Region B the middle range around the peak, from about 30 to 170, and Region C the heavy nuclei beyond about 170). Indicate which region corresponds to: (1) nuclei prone to fission, (2) nuclei prone to fusion, (3) most stable nuclei.
- Heavy nuclei (Region C) have a lower binding energy per nucleon than middle ones: splitting them into two middle nuclei releases energy. They are prone to fission.
- Light nuclei (Region A) have a low binding energy per nucleon: joining them into a heavier nucleus releases energy. They are prone to fusion.
- Region B, around the maximum near iron, has the highest binding energy per nucleon: the most stable nuclei.
(i)(b) In Rutherford's scattering experiment when an alpha particle (charge , mass ) approaches a gold nucleus (), it is continuously repelled, so it loses its kinetic energy (K) and its potential energy increases. Finally, the α-particle comes to rest momentarily when whole of the kinetic energy is changed into the potential energy of the charge at that distance from the nucleus. Let this distance be , after which the α-particle returns back again due to electrostatic repulsion. Using the above information, derive an expression for .
- Potential energy of the α-particle (charge ) at distance from the nucleus (charge ): .
- At the distance of closest approach all of K has become U: .
- for gold.
(ii)(a) OR: In an atom X, electrons absorb the energy from an external source. This energy excites the electrons from a lower-energy level to a higher-energy level around the nucleus of the atom. When electrons return to the ground state, they emit photons. Figure 15 is the energy level diagram of atom X with three energy levels, E₁ = 0.00 eV, E₂ = 1.78 eV and E₃ = 2.95 eV. The ground state is considered 0 eV for reference. What wavelength of radiation is needed to excite the atom to energy level E₂ from E₁?
- Photon energy needed: .
- .
- (about 695 nm, red light).
(ii)(b)(1) According to Bohr's theory of hydrogen atom, calculate the angular momentum of the electron in second Bohr orbit.
- Bohr's quantisation: . For : .
- .
(ii)(b)(2) Radius of the third Bohr orbit.
- . For : .
Question 20 (5 marks)
Semiconductor devices: LED and junction- (i)(a)Identify the wavelength (the LED) that has the maximum energy gap.
- (i)(b)The minimum energy gap.
- (ii)(a)E is the energy of the incident photon and is the energy gap, across the depletion layer. What will happen when ?
- (ii)(b)
- (ii)(c)
Tests: Band gap from an LED's turn-on voltage; photon absorption at a p-n junction.
Show solution
(i)(a) Identify the wavelength (the LED) that has the maximum energy gap.
- An LED starts conducting (and glowing) when , so the larger the turn-on (threshold) voltage, the larger the band gap.
- Line 3 turns on at the highest voltage: largest , and so the shortest wavelength, .
(i)(b) The minimum energy gap.
- Line 1 turns on at the lowest voltage: smallest , longest wavelength.
(ii)(a) E is the energy of the incident photon and is the energy gap, across the depletion layer. What will happen when ?
- The photon is absorbed and creates an electron-hole pair; the junction field separates them, giving a photocurrent.
- The extra energy goes to the carriers as kinetic energy and is soon lost as heat.
(ii)(b)
- The photon has just enough energy: it is absorbed and creates an electron-hole pair with no energy to spare.
(ii)(c)
- The photon cannot lift an electron across the gap: it is not absorbed (the material is transparent to it), so no electron-hole pair and no photocurrent.
Questions are quoted from the ISC 2026 Physics Specimen Question Paper (861A); figures are described in words. Every final answer is checked against the official CISCE answers. Where a question offers a choice, every option is solved.
CISCE specimen question papers and their answers are referenced for educational and review purposes only, under fair dealing. All copyrights in the questions belong to the Council for the Indian School Certificate Examinations. Solutions and explanations provided here are original works by Your Abhyaasika, generated with AI, and may contain mistakes. Your Abhyaasika is not affiliated with CISCE.