AI-generated solutions. The solutions and explanations on this page are written by AI. We check the final answers with automated tests, but AI can still make mistakes, especially in explanations and in figures described in words. If something looks wrong, ask in the doubt chat on that question or check with your teacher.
ScienceClass 10CBSE
Class 10 Science Chapter 11 Exercise Questions and Answers
Step-by-step solutions to every in-text and end-of-chapter question in NCERT Class 10 Science Chapter 11. Every numerical answer is recomputed from the question's own numbers: Ohm's law, series and parallel resistors, heating and power.
NCERT solutions for the end-of-chapter exercise questions of Class 10 Science Chapter 11 Electricity: all 18 questions answered step by step, as ideal answers in the CBSE board format. Free, with a doubt chat on every question.
Key ideas
Current I=tQ (ampere); potential difference V=QW (volt); Ohm's law V=IR.
R=ρAl: resistance grows with length, falls with area, and depends on the material.
Series: R=R1+R2+…, same current. Parallel: R1=R11+R21+…, same voltage.
Heating: H=I2Rt. Power: P=VI=I2R=RV2. Energy in kWh = kW × hours.
An ammeter goes in series; a voltmeter goes in parallel.
Exercises (end of chapter)
Q1
Chapter 11 exercise, Question 1
A piece of wire of resistance R is cut into five equal parts. These parts are then connected in parallel. If the equivalent resistance of this combination is R′, then the ratio R/R′ is (a) 1/25 (b) 1/5 (c) 5 (d) 25.
Tests: Combining cutting (length) and parallel connection.
Show solution
Each part has resistance 5R. Five equal resistors in parallel: R′=5R/5=25R. So R′R=25.
Answer(d) 25
Ask about this question
Q2
Chapter 11 exercise, Question 2
Which of the following terms does not represent electrical power in a circuit? (a) I²R (b) IR² (c) VI (d) V²/R
Tests: Deriving the forms of electric power.
Show solution
P=VI; with V=IR, P=I2R=RV2. IR2 is not power.
Answer(b) IR²
Ask about this question
Q3
Chapter 11 exercise, Question 3
An electric bulb is rated 220 V and 100 W. When it is operated on 110 V, the power consumed will be (a) 100 W (b) 75 W (c) 50 W (d) 25 W.
Tests: Using the bulb's fixed resistance to find power at another voltage.
Show solution
R=PV2=1002202=484Ω
At 110 V: P=4841102=25 W
Answer(d) 25 W
Ask about this question
Q4
Chapter 11 exercise, Question 4
Two conducting wires of the same material and of equal lengths and equal diameters are first connected in series and then in parallel in a circuit across the same potential difference. The ratio of heat produced in series and parallel combinations would be (a) 1:2 (b) 2:1 (c) 1:4 (d) 4:1.
Tests: Comparing heating in series and parallel at the same voltage.
Show solution
Each wire has resistance R. Series: 2R; parallel: 2R.
At the same V, H=RV2t, so Hs:Hp=2R1:R2=1:4.
Answer(c) 1:4
Ask about this question
Q5
Chapter 11 exercise, Question 5
How is a voltmeter connected in the circuit to measure the potential difference between two points?
Tests: Connecting a voltmeter correctly.
Show solution
In parallel, across the two points. Its high resistance means it draws almost no current from the circuit.
AnswerIn parallel across the two points.
Ask about this question
Q6
Chapter 11 exercise, Question 6
A copper wire has diameter 0.5 mm and resistivity of 1.6 × 10⁻⁸ Ω m. What will be the length of this wire to make its resistance 10 Ω? How much does the resistance change if the diameter is doubled?
Tests: Using R = ρl/A with a circular cross-section.
Show solution
r=0.25mm=2.5×10−4 m; A=πr2≈1.96×10−7m2.
l=ρRA=1.6×10−810×1.96×10−7≈122.7 m
Doubling the diameter makes the area 4 times, so R becomes 410=2.5Ω: it falls to a quarter.
AnswerAbout 122.7 m; the resistance becomes 2.5 Ω (one quarter).
Ask about this question
Q7
Chapter 11 exercise, Question 7
The values of current I flowing in a given resistor for the corresponding values of potential difference V across the resistor are: I = 0.5, 1.0, 2.0, 3.0, 4.0 A and V = 1.6, 3.4, 6.7, 10.2, 13.2 V. Plot a graph between V and I and calculate the resistance of that resistor.
Tests: Finding resistance as the slope of a V-I graph.
Show solution
Plot V on the y-axis against I on the x-axis. The points lie close to a straight line through the origin, so Ohm's law holds.
Slope =ΔIΔV, for example 4.0−1.013.2−3.4≈3.3; the best line gives about 3.4Ω.
AnswerAbout 3.4 Ω (the slope of the V-I line).
Ask about this question
Q8
Chapter 11 exercise, Question 8
When a 12 V battery is connected across an unknown resistor, there is a current of 2.5 mA in the circuit. Find the value of the resistance of the resistor.
Tests: Applying Ohm's law with unit conversion.
Show solution
R=IV=2.5×10−312=4800Ω=4.8kΩ
Answer4800 Ω (4.8 kΩ)
Ask about this question
Q9
Chapter 11 exercise, Question 9
A battery of 9 V is connected in series with resistors of 0.2 Ω, 0.3 Ω, 0.4 Ω, 0.5 Ω and 12 Ω, respectively. How much current would flow through the 12 Ω resistor?
Tests: Using the fact that series resistors carry the same current.
Show solution
R=0.2+0.3+0.4+0.5+12=13.4Ω
In series the same current flows through every resistor: I=13.49≈0.67 A
AnswerAbout 0.67 A
Ask about this question
Q10
Chapter 11 exercise, Question 10
How many 176 Ω resistors (in parallel) are required to carry 5 A on a 220 V line?
Tests: Finding the number of equal resistors in parallel for a required current.
Show solution
Required R=5220=44Ω.
n equal resistors in parallel: n176=44, so n=4.
Answer4 resistors
Ask about this question
Q11
Chapter 11 exercise, Question 11
Show how you would connect three resistors, each of resistance 6 Ω, so that the combination has a resistance of
(i)
9 Ω
(ii)
4 Ω
Tests: Designing combinations of equal resistors.
Show solution
(i)9 Ω
Two in parallel give 3 Ω; the third in series: 3+6=9Ω.
AnswerTwo in parallel, in series with the third.
(ii)4 Ω
Two in series give 12 Ω; the third in parallel: 1812×6=4Ω.
AnswerTwo in series, in parallel with the third.
Ask about this question
Q12
Chapter 11 exercise, Question 12
Several electric bulbs designed to be used on a 220 V electric supply line are rated 10 W. How many lamps can be connected in parallel with each other across the two wires of the 220 V line if the maximum allowable current is 5 A?
Tests: Using the power limit of a supply line.
Show solution
Maximum power =VI=220×5=1100 W.
Number of 10 W bulbs =101100=110.
Answer110 lamps
Ask about this question
Q13
Chapter 11 exercise, Question 13
A hot plate of an electric oven connected to a 220 V line has two resistance coils A and B, each of 24 Ω resistance, which may be used separately, in series, or in parallel. What are the currents in the three cases?
Tests: Finding the current for each combination at fixed voltage.
Show solution
One coil: I=24220≈9.17 A.
Series (48Ω): I=48220≈4.58 A.
Parallel (12Ω): I=12220≈18.33 A.
AnswerSeparately 9.17 A; in series 4.58 A; in parallel 18.33 A.
Ask about this question
Q14
Chapter 11 exercise, Question 14
Compare the power used in the 2 Ω resistor in each of the following circuits: (i) a 6 V battery in series with 1 Ω and 2 Ω resistors, and (ii) a 4 V battery in parallel with 12 Ω and 2 Ω resistors.
Tests: Finding the power in one resistor of a circuit.
Show solution
(i) R=1+2=3Ω, I=36=2 A, P=I2R=4×2=8 W.
(ii) In parallel the 2 Ω gets the full 4 V: P=RV2=216=8 W.
Answer8 W in both: the power is the same.
Ask about this question
Q15
Chapter 11 exercise, Question 15
Two lamps, one rated 100 W at 220 V, and the other 60 W at 220 V, are connected in parallel to the electric mains supply. What current is drawn from the line if the supply voltage is 220 V?
Tests: Adding powers of devices in parallel.
Show solution
Both run at their rated 220 V, so total P=100+60=160 W.
I=VP=220160≈0.73 A
AnswerAbout 0.73 A
Ask about this question
Q16
Chapter 11 exercise, Question 16
Which uses more energy, a 250 W TV set in 1 hr, or a 1200 W toaster in 10 minutes?
Tests: Comparing energy, not power.
Show solution
TV: 250×1=250 Wh. Toaster: 1200×6010=200 Wh.
AnswerThe TV set (250 Wh against 200 Wh).
Ask about this question
Q17
Chapter 11 exercise, Question 17
An electric heater of resistance 8 Ω draws 15 A from the service mains for 2 hours. Calculate the rate at which heat is developed in the heater.
Tests: Recognising that the rate of heating is power.
Show solution
Rate of heating = power: P=I2R=152×8=1800 W (1800 J every second).
Answer1800 W (1800 J/s)
Ask about this question
Q18
Chapter 11 exercise, Question 18
Explain the following.
(a)
Why is tungsten used almost exclusively for filaments of electric lamps?
(b)
Why are the conductors of electric heating devices, such as bread-toasters and electric irons, made of an alloy rather than a pure metal?
(c)
Why is the series arrangement not used for domestic circuits?
(d)
How does the resistance of a wire vary with its area of cross-section?
(e)
Why are copper and aluminium wires usually employed for electricity transmission?
Tests: Explaining material and wiring choices from resistance and heating.
Show solution
(a)Why is tungsten used almost exclusively for filaments of electric lamps?
Tungsten has a very high melting point (about 3380 °C), so it can glow white-hot without melting.
AnswerIts very high melting point lets it glow without melting.
(b)Why are the conductors of electric heating devices, such as bread-toasters and electric irons, made of an alloy rather than a pure metal?
Alloys have higher resistivity, so they produce more heat, and they do not oxidise (burn) readily at high temperatures.
AnswerHigh resistivity and no oxidation at high temperature.
(c)Why is the series arrangement not used for domestic circuits?
In series the voltage is shared, so devices don't get their rated voltage; the total resistance is large; and if one device fails or is switched off, all stop.
AnswerVoltage is shared, the current is small, and one failure stops everything.
(d)How does the resistance of a wire vary with its area of cross-section?
Inversely: R∝A1. A thicker wire has less resistance.
AnswerResistance is inversely proportional to the area of cross-section.
(e)Why are copper and aluminium wires usually employed for electricity transmission?
They have very low resistivity, so little energy is lost as heat, and they are cheaper than silver.
AnswerThey are good conductors (low resistivity) and affordable.
Questions from the NCERT textbook are reproduced for educational and review purposes only, under fair dealing. All copyrights in the questions belong to NCERT. Solutions and explanations provided here are original works by Your Abhyaasika, generated with AI, and may contain mistakes. Your Abhyaasika is not affiliated with CBSE or NCERT.
Check yourself on this chapter
Practise with fresh questions at your level, free: 10 questions a day with an account.