AI-generated solutions. The solutions and explanations on this page are written by AI. We check the final answers with automated tests, but AI can still make mistakes, especially in explanations and in figures described in words. If something looks wrong, ask in the doubt chat on that question or check with your teacher.

Class 10 Science Chapter 11 Intext Questions and Answers

Step-by-step solutions to every in-text and end-of-chapter question in NCERT Class 10 Science Chapter 11. Every numerical answer is recomputed from the question's own numbers: Ohm's law, series and parallel resistors, heating and power.

NCERT solutions for the intext questions of Class 10 Science Chapter 11 Electricity: all 23 questions answered step by step, as ideal answers in the CBSE board format. Free, with a doubt chat on every question.

Key ideas
  • Current I=QtI = \dfrac{Q}{t} (ampere); potential difference V=WQV = \dfrac{W}{Q} (volt); Ohm's law V=IRV = IR.
  • R=ρlAR = \rho \dfrac{l}{A}: resistance grows with length, falls with area, and depends on the material.
  • Series: R=R1+R2+…R = R_1 + R_2 + \dots, same current. Parallel: 1R=1R1+1R2+…\dfrac{1}{R} = \dfrac{1}{R_1} + \dfrac{1}{R_2} + \dots, same voltage.
  • Heating: H=I2RtH = I^2Rt. Power: P=VI=I2R=V2RP = VI = I^2R = \dfrac{V^2}{R}. Energy in kWh = kW × hours.
  • An ammeter goes in series; a voltmeter goes in parallel.

In-text questions: electric current and circuit (after 11.1)

Q1

Section 11.1, Intext question 1

What does an electric circuit mean?

Tests: Defining an electric circuit.

Show solution
  1. A continuous and closed path along which an electric current flows, for example a cell, a switch, wires and a bulb joined end to end.
AnswerA continuous, closed path of an electric current.
Ask about this question
Q2

Section 11.1, Intext question 2

Define the unit of current.

Tests: Defining the ampere from charge and time.

Show solution
  1. The SI unit of current is the ampere (A). Since I=QtI = \dfrac{Q}{t}, one ampere is the current when one coulomb of charge flows through a cross-section in one second.
Answer1 ampere = 1 coulomb of charge flowing per second.
Ask about this question
Q3

Section 11.1, Intext question 3

Calculate the number of electrons constituting one coulomb of charge.

Tests: Using the charge on an electron to count electrons.

Show solution
  1. Charge on one electron =1.6×10−19= 1.6 \times 10^{-19} C.
  2. n=Qe=11.6×10−19=6.25×1018n = \dfrac{Q}{e} = \dfrac{1}{1.6 \times 10^{-19}} = 6.25 \times 10^{18}
Answer6.25×10186.25 \times 10^{18} electrons
Ask about this question

In-text questions: potential and potential difference (after 11.2)

Q1

Section 11.2, Intext question 1

Name a device that helps to maintain a potential difference across a conductor.

Tests: Naming the source of potential difference in a circuit.

Show solution
  1. A cell or a battery (a combination of cells). The chemical reaction inside it maintains the potential difference.
AnswerA cell or a battery.
Ask about this question
Q2

Section 11.2, Intext question 2

What is meant by saying that the potential difference between two points is 1 V?

Tests: Defining the volt from work and charge.

Show solution
  1. V=WQV = \dfrac{W}{Q}. A potential difference of 1 V means 1 joule of work is done to move 1 coulomb of charge from one point to the other.
Answer1 J of work is done in moving 1 C of charge between the two points.
Ask about this question
Q3

Section 11.2, Intext question 3

How much energy is given to each coulomb of charge passing through a 6 V battery?

Tests: Using W = VQ.

Show solution
  1. W=VQ=6×1=6W = VQ = 6 \times 1 = 6 J
Answer6 J
Ask about this question

In-text questions: factors on which resistance depends (after 11.5)

Q1

Section 11.5, Intext question 1

On what factors does the resistance of a conductor depend?

Tests: Stating how length, area and material affect resistance.

Show solution
  1. Length: R∝lR \propto l. Area of cross-section: R∝1AR \propto \dfrac{1}{A}. Material: through its resistivity ρ\rho. Together R=ρlAR = \rho \dfrac{l}{A}.
  2. Resistance also depends on temperature (it rises with temperature for metals).
AnswerLength, area of cross-section, material (resistivity) and temperature: R=ρlAR = \rho \dfrac{l}{A}.
Ask about this question
Q2

Section 11.5, Intext question 2

Will current flow more easily through a thick wire or a thin wire of the same material, when connected to the same source? Why?

Tests: Relating thickness to resistance.

Show solution
  1. Through the thick wire. R∝1AR \propto \dfrac{1}{A}, so a thicker wire (larger area) has less resistance and a larger current flows from the same source.
AnswerThrough the thick wire, because its larger area gives it a smaller resistance.
Ask about this question
Q3

Section 11.5, Intext question 3

Let the resistance of an electrical component remain constant while the potential difference across its two ends decreases to half of its former value. What change will occur in the current through it?

Tests: Applying Ohm's law to a change in voltage.

Show solution
  1. I=VRI = \dfrac{V}{R}. With R constant, halving V halves I.
AnswerThe current becomes half.
Ask about this question
Q4

Section 11.5, Intext question 4

Why are coils of electric toasters and electric irons made of an alloy rather than a pure metal?

Tests: Choosing materials for heating elements.

Show solution
  1. An alloy such as nichrome has a higher resistivity than its metals, so it produces more heat, and it does not oxidise (burn) readily at high temperatures.
AnswerAlloys have higher resistivity and do not oxidise easily when hot.
Ask about this question
Q5

Section 11.5, Intext question 5

Use the data in Table 11.2 (resistivities at 20 °C) to answer the following.
  1. (a)
    Which among iron and mercury is a better conductor?
  2. (b)
    Which material is the best conductor?

Tests: Comparing conductors by resistivity.

Show solution

(a) Which among iron and mercury is a better conductor?

  1. Iron 10.0×10−8 Ω m10.0 \times 10^{-8}\ \Omega\,\text{m}, mercury 94.0×10−8 Ω m94.0 \times 10^{-8}\ \Omega\,\text{m}. Lower resistivity conducts better: iron.
AnswerIron

(b) Which material is the best conductor?

  1. Silver has the lowest resistivity in the table, 1.60×10−8 Ω m1.60 \times 10^{-8}\ \Omega\,\text{m}.
AnswerSilver
Ask about this question

In-text questions: resistors in series (after 11.6.1)

Q1

Section 11.6.1, Intext question 1

Draw a schematic diagram of a circuit consisting of a battery of three cells of 2 V each, a 5 Ω resistor, an 8 Ω resistor, a 12 Ω resistor and a plug key, all connected in series.

Tests: Drawing a series circuit with standard symbols.

Show solution
  1. Draw three cells end to end (total 6 V), then the plug key, then the 5 Ω, 8 Ω and 12 Ω resistors one after another, and close the loop back to the battery. There is only one path for the current.
AnswerOne loop: battery (3 × 2 V), plug key, 5 Ω, 8 Ω and 12 Ω resistors, all in series.
Ask about this question
Q2

Section 11.6.1, Intext question 2

Redraw the circuit of Question 1, putting in an ammeter to measure the current through the resistors and a voltmeter to measure the potential difference across the 12 Ω resistor. What would be the readings in the ammeter and the voltmeter?

Tests: Using series resistance and Ohm's law to predict meter readings.

Show solution
  1. Total resistance R=5+8+12=25 ΩR = 5 + 8 + 12 = 25\ \Omega; battery V=3×2=6V = 3 \times 2 = 6 V.
  2. Ammeter (in series): I=625=0.24I = \dfrac{6}{25} = 0.24 A.
  3. Voltmeter (across 12 Ω): V=IR=0.24×12=2.88V = IR = 0.24 \times 12 = 2.88 V.
AnswerAmmeter 0.24 A; voltmeter 2.88 V.
Ask about this question

In-text questions: resistors in parallel (after 11.6.2)

Q1

Section 11.6.2, Intext question 1

Judge the equivalent resistance when the following are connected in parallel.
  1. (a)
    1 Ω and 10⁶ Ω
  2. (b)
    1 Ω, 10³ Ω and 10⁶ Ω

Tests: Estimating a parallel combination with one small resistor.

Show solution

(a) 1 Ω and 10⁶ Ω

  1. 1R=1+10−6\dfrac{1}{R} = 1 + 10^{-6}, so R≈0.999999 ΩR \approx 0.999999\ \Omega: just under 1 Ω.
AnswerAbout 1 Ω (slightly less).

(b) 1 Ω, 10³ Ω and 10⁶ Ω

  1. 1R=1+10−3+10−6\dfrac{1}{R} = 1 + 10^{-3} + 10^{-6}, so R≈0.999 ΩR \approx 0.999\ \Omega: again just under 1 Ω.
AnswerAbout 1 Ω (slightly less).
Ask about this question
Q2

Section 11.6.2, Intext question 2

An electric lamp of 100 Ω, a toaster of resistance 50 Ω, and a water filter of resistance 500 Ω are connected in parallel to a 220 V source. What is the resistance of an electric iron connected to the same source that takes as much current as all three appliances, and what is the current through it?

Tests: Finding an equivalent parallel resistance and the current it draws.

Show solution
  1. 1R=1100+150+1500=5+10+1500=16500\dfrac{1}{R} = \dfrac{1}{100} + \dfrac{1}{50} + \dfrac{1}{500} = \dfrac{5 + 10 + 1}{500} = \dfrac{16}{500}, so R=31.25 ΩR = 31.25\ \Omega.
  2. I=VR=22031.25=7.04I = \dfrac{V}{R} = \dfrac{220}{31.25} = 7.04 A
Answer31.25 Ω; 7.04 A
Ask about this question
Q3

Section 11.6.2, Intext question 3

What are the advantages of connecting electrical devices in parallel with the battery instead of connecting them in series?

Tests: Explaining why parallel wiring is used.

Show solution
  1. Each device gets the full supply voltage, so it works at its rated power.
  2. Each device can be switched on or off on its own, and one failing does not stop the others.
  3. Each device draws the current it needs, according to its own resistance.
AnswerEach device gets the full voltage, works independently, and draws its own current.
Ask about this question
Q4

Section 11.6.2, Intext question 4

How can three resistors of resistances 2 Ω, 3 Ω and 6 Ω be connected to give a total resistance of
  1. (a)
    4 Ω?
  2. (b)
    1 Ω?

Tests: Designing a combination of resistors for a target resistance.

Show solution

(a) 4 Ω?

  1. 3 Ω and 6 Ω in parallel give 3×63+6=2 Ω\dfrac{3 \times 6}{3 + 6} = 2\ \Omega; add the 2 Ω in series: 2+2=4 Ω2 + 2 = 4\ \Omega.
Answer3 Ω and 6 Ω in parallel, in series with 2 Ω.

(b) 1 Ω?

  1. All three in parallel: 1R=12+13+16=1\dfrac{1}{R} = \dfrac{1}{2} + \dfrac{1}{3} + \dfrac{1}{6} = 1, so R=1 ΩR = 1\ \Omega.
AnswerAll three in parallel.
Ask about this question
Q5

Section 11.6.2, Intext question 5

What is (a) the highest, (b) the lowest total resistance that can be secured by combinations of four coils of resistance 4 Ω, 8 Ω, 12 Ω and 24 Ω?

Tests: Using series for the largest and parallel for the smallest resistance.

Show solution
  1. Highest: all in series, 4+8+12+24=48 Ω4 + 8 + 12 + 24 = 48\ \Omega.
  2. Lowest: all in parallel, 1R=14+18+112+124=6+3+2+124=12\dfrac{1}{R} = \dfrac{1}{4} + \dfrac{1}{8} + \dfrac{1}{12} + \dfrac{1}{24} = \dfrac{6 + 3 + 2 + 1}{24} = \dfrac{1}{2}, so R=2 ΩR = 2\ \Omega.
Answer(a) 48 Ω (b) 2 Ω
Ask about this question

In-text questions: heating effect of electric current (after 11.7)

Q1

Section 11.7, Intext question 1

Why does the cord of an electric heater not glow while the heating element does?

Tests: Applying H = I²Rt to parts of one circuit.

Show solution
  1. The same current flows through both. Heat produced is H=I2RtH = I^2Rt. The copper cord has very low resistance, so little heat is produced; the nichrome element has high resistance, so it gets hot enough to glow.
AnswerThe cord's resistance is very low, so it produces little heat; the element's high resistance makes it glow.
Ask about this question
Q2

Section 11.7, Intext question 2

Compute the heat generated while transferring 96000 coulomb of charge in one hour through a potential difference of 50 V.

Tests: Using H = VQ.

Show solution
  1. H=VQ=50×96000=4.8×106H = VQ = 50 \times 96000 = 4.8 \times 10^{6} J
Answer4.8×1064.8 \times 10^{6} J
Ask about this question
Q3

Section 11.7, Intext question 3

An electric iron of resistance 20 Ω takes a current of 5 A. Calculate the heat developed in 30 s.

Tests: Using Joule's law of heating.

Show solution
  1. H=I2Rt=52×20×30=15000H = I^2Rt = 5^2 \times 20 \times 30 = 15000 J =1.5×104= 1.5 \times 10^{4} J
Answer1.5×1041.5 \times 10^{4} J
Ask about this question

In-text questions: electric power (after 11.8)

Q1

Section 11.8, Intext question 1

What determines the rate at which energy is delivered by a current?

Tests: Linking electric power to the rate of energy transfer.

Show solution
  1. Electric power, P=VI=I2R=V2RP = VI = I^2R = \dfrac{V^2}{R}, is the rate at which electrical energy is delivered.
AnswerThe electric power, P = VI.
Ask about this question
Q2

Section 11.8, Intext question 2

An electric motor takes 5 A from a 220 V line. Determine the power of the motor and the energy consumed in 2 h.

Tests: Calculating power and energy, with units.

Show solution
  1. P=VI=220×5=1100P = VI = 220 \times 5 = 1100 W
  2. E=Pt=1100×2=2200E = Pt = 1100 \times 2 = 2200 Wh =2.2= 2.2 kWh =7.92×106= 7.92 \times 10^{6} J
Answer1100 W; 2.2 kWh (7.92×1067.92 \times 10^{6} J)
Ask about this question

Chapter notes

Questions are from the NCERT Class 10 Science textbook, Chapter 11; word problems are paraphrased with every number kept.

Questions from the NCERT textbook are reproduced for educational and review purposes only, under fair dealing. All copyrights in the questions belong to NCERT. Solutions and explanations provided here are original works by Your Abhyaasika, generated with AI, and may contain mistakes. Your Abhyaasika is not affiliated with CBSE or NCERT.

Check yourself on this chapter

Practise with fresh questions at your level, free: 10 questions a day with an account.